Nissan Almera Tino V10. Instruction — part 508
EC-858
[QG (WITHOUT EURO-OBD)]
HO2S1 (A/T MODELS)
12.
CHECK PCV VALVE
Refer to
EC-934, "Component Inspection"
.
OK or NG
OK
>> GO TO 13.
NG
>> Replace PCV valve.
13.
CHECK HEATED OXYGEN SENSOR 1
Refer to
EC-858, "Component Inspection"
.
OK or NG
OK
>> GO TO 14.
NG
>> Replace malfunctioning heated oxygen sensor 1.
14.
CHECK INTERMITTENT INCIDENT
Refer to
EC-644, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
.
>> INSPECTION END
Component Inspection
EBS00R2G
HEATED OXYGEN SENSOR 1
With CONSULT-II
1.
Start engine and warm it up to normal operating temperature.
2.
Select “MANU TRIG” and adjust “TRIGGER POINT” to 100% in “DATA MONITOR” mode with CONSULT-
II.
3.
Select “HO2S1 (B1)/(B2)” and “HO2S1 MNTR (B1)/(B2)”.
4.
Hold engine speed at 2,000 rpm under no load during the following steps.
5.
Touch “RECORD” on CONSULT-II screen.
6.
Check the following.
●
“HO2S1 MNTR (B1)/(B2)” in “DATA MONITOR” mode
changes from “RICH” to “LEAN” to “RICH” more than 5 times
in 10 seconds.
5 times (cycles) are counted as shown at right.
●
“HO2S1 (B1)/(B2)” voltage goes above 0.6V at least once.
●
“HO2S1 (B1)/(B2)” voltage goes below 0.3V at least once.
●
“HO2S1 (B1)/(B2)” voltage never exceeds 1.0V.
SEF646Y
SEF647Y
HO2S1 (A/T MODELS)
EC-859
[QG (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
CAUTION:
●
Discard any heated oxygen sensor which has been dropped from a height of more than 0.5 m (19.7
in) onto a hard surface such as a concrete floor; use a new one.
●
Before installing new oxygen sensor, clean exhaust system threads using Oxygen Sensor Thread
Cleaner tool J-43897-18 or J-43897-12 and approved anti-seize lubricant.
Without CONSULT-II
1.
Start engine and warm it up to normal operating temperature.
2.
Set voltmeter probes between ECM terminal 35 [HO2S1 (B1) signal] or 36 [HO2S1 (B2) signal] and
engine ground.
3.
Check the following with engine speed held at 2,000 rpm con-
stant under no load.
●
The voltage fluctuates between 0 to 0.3V and 0.6 to 1.0V
more than 5 times within 10 seconds.
●
The maximum voltage is over 0.6V at least one time.
●
The minimum voltage is below 0.3V at least one time.
●
The voltage never exceeds 1.0V.
1 time: 0 - 0.3V
→
0.6 - 1.0V
→
0 - 0.3V
2 times: 0 - 0.3V
→
0.6 - 1.0V
→
0 - 0.3V
→
0.6 - 1.0V
CAUTION:
●
Discard any heated oxygen sensor which has been dropped
from a height of more than 0.5 m (19.7 in) onto a hard surface such as a concrete floor; use a new
one.
●
Before installing new oxygen sensor, clean exhaust system threads using Oxygen Sensor Thread
Cleaner tool J-43897-18 or J-43897-12 and approved anti-seize lubricant.
Removal and Installation
EBS00R2H
HEATED OXYGEN SENSOR 1
Refer to
EM-21, "EXHAUST MANIFOLD AND CATALYTIC CONVERTER"
.
SEF648Y
MBIB0019E
EC-860
[QG (WITHOUT EURO-OBD)]
HO2S2 (M/T MODELS)
HO2S2 (M/T MODELS)
PFP:226A0
Component Description
EBS00R2I
The heated oxygen sensor 2, after three way catalyst (manifold),
monitors the oxygen level in the exhaust gas.
Even if switching characteristics of the heated oxygen sensor 1 are
shifted, the air-fuel ratio is controlled to stoichiometric, by the signal
from the heated oxygen sensor 2.
This sensor is made of ceramic zirconia. The zirconia generates volt-
age from approximately 1V in richer conditions to 0V in leaner condi-
tions.
Under normal conditions the heated oxygen sensor 2 is not used for
engine control operation.
CONSULT-II Reference Value in Data Monitor Mode
EBS00R2J
Specification data are reference values.
SEF327R
MONITOR ITEM
CONDITION
SPECIFICATION
HO2S2 (B1)
●
Engine: After warming up
●
Keeping the engine speed
between 3,500 and 4,000 rpm
for one minute and at idle for
one minute under no load
Revving engine from idle to 3,000
rpm quickly.
0 - 0.3V
←→
Approx. 0.6 - 1.0V
HO2S2 MNTR (B1)
LEAN
←→
RICH
HO2S2 (M/T MODELS)
EC-861
[QG (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
Wiring Diagram
EBS00R2K
YEC485A
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст