Nissan Almera Tino V10. Instruction — part 901
JLC356B
JLC338B
REGULATOR VALVE INSPECTION
NLLC0046
1.
Visually inspect components for wear and damage.
2.
Check oil pressure regulator valve sliding surface and valve
spring.
3.
Coat regulator valve with engine oil. Check that it falls
smoothly into the valve hole by its own weight.
If damaged, replace regulator valve set or oil pump body.
JLC358B
4.
Check regulator valve to oil pump body clearance.
Clearance 6:
6 : 0.040 - 0.097 mm (0.0016 - 0.0038 in)
If it exceeds the limit, replace oil pump body.
ENGINE LUBRICATION SYSTEM
YD
Oil Pump (Cont’d)
LC-26
SLC287B
JLC288B
Changing Engine Oil
NLLC0074
WARNING:
I
Be careful not to burn yourself, as the engine oil is hot.
I
Prolonged and repeated contact with used engine oil may
cause skin cancer; try to avoid direct skin contact with
used oil. If skin contact is made, wash thoroughly with
soap or hand cleaner as soon as possible.
1.
Warm up engine, and check for oil leakage from engine com-
ponents.
2.
Stop engine and wait more than 10 minutes.
3.
Remove drain plug and oil filler cap.
4.
Drain oil and refill with new engine oil.
Oil Specification and Viscosity:
I
API grade CF-4
I
ACEA grade B1, B3
Refer to MA-20, “RECOMMENDED FLUIDS AND LUBRI-
CANTS”.
Refill oil capacity (Approximately):
Unit:
(Imp qt)
Drain and refill
Without oil filter
chang
e
4.9 (4 - 3/8
)
With oil filter
chang
e
5.2 (4 - 5/8
)
Dry engine (engine overhaul
) 6.3 (5 - 1/2
)
CAUTION:
I
Be sure to clean drain plug and install with new washer.
Drain plug:
: 29 - 39 N·m (3.0 - 4.0 kg-m, 22 - 29 ft-lb)
I
The refill capacity depends on the oil temperature and
drain time. Use these specifications for reference only.
Always use the dipstick to determine when the proper
amount of oil is in the engine.
5.
Check oil level.
6.
Start engine and check area around drain plug and oil filter for
oil leakage.
7.
Run engine for a few minutes, then turn it off. After several
minutes, check oil level.
GI
MA
EM
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ENGINE LUBRICATION SYSTEM
YD
Changing Engine Oil
LC-27
Oil Filter Bracket
NLLC0075
MBIB1012E
REMOVAL AND INSTALLATION
NLLC0075S01
1.
Remove the undercover.
2.
Steer the front wheel to the right.
3.
Remove the right splash cover.
4.
Remove the oil filter bracket bolt.
5.
Reinstall all removed parts in the reverse order of removal.
I
Insert the top mounting bolt to the oil filter bracket beforehand,
and set the oil filter bracket to the installation location.
MBIB1013E
Changing Oil Filter
NLLC0076
ENGINE LUBRICATION SYSTEM
YD
Oil Filter Bracket
LC-28
JLC290B
REMOVAL
NLLC0076S01
1.
Using a socket wrench [plane-to-plane width: 17 mm (0.67 in)],
loosen the oil filter approximately four turns.
JLC291B
2.
Drain the oil after matching the “DRAIN” arrow mark at the
bottom of the oil filter to the protrusion on the oil filter bracket.
I
Catch the oil with a pan or cloth.
CAUTION:
I
The drained oil flows over the right surface of the oil fil-
ter.
I
Completely wipe clean any engine oil remaining on the oil
filter or vehicle.
3.
Remove the oil filter.
JLC292B
4.
Remove the O-ring from the oil filter.
I
Push the O-ring in one direction, lift the slack part using
fingers, and remove the O-ring from the oil filter.
CAUTION:
Do not use wires or flat-bladed screwdrivers etc. as they may
cause damage to the oil filter.
INSTALLATION
NLLC0076S02
1.
Completely remove all foreign objects adhering to the inside of
the oil filter or O-ring mounting area (filter side and bracket
side).
2.
Install O-ring to the oil filter.
3.
Install the oil filter to the oil filter bracket.
: 20 - 24 N·m (2.0 - 2.5 kg-m, 15 - 18 ft-lb)
4.
After warming up the engine, check for engine oil leakage.
GI
MA
EM
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ENGINE LUBRICATION SYSTEM
YD
Changing Oil Filter (Cont’d)
LC-29
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст