Nissan Almera Tino V10. Instruction — part 603
EC-1238
[YD (WITH EURO-OBD)]
BRAKE SWITCH
2.
Check continuity between stop lamp switch terminals 1 and 2
under the following conditions.
If NG, adjust brake pedal installation, refer to BR-14, “BRAKE
PEDAL AND BRACKET”, and perform step 2 again.
Conditions
Continuity
Brake pedal fully released
Should not exist.
Brake pedal depressed
Should exist.
PBIB0118E
PNP SWITCH
EC-1239
[YD (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
PNP SWITCH
PFP:32006
Description
EBS013I0
When the gear position is in Neutral, park/neutral position is ON. ECM detects the position because the conti-
nuity of the line (the “ON” signal) exists.
CONSULT-II Reference Value in Data Monitor Mode
EBS013I1
Specification data are reference values.
ECM Terminals and Reference Value
EBS013I2
Specification data are reference values and are measured between each terminal and ground.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
MONITOR ITEM
CONDITION
SPECIFICATION
P/N POSI SW
●
Ignition switch: ON
Shift lever: Neutral position
ON
Except above
OFF
TERMI-
NAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA
(DC Voltage)
110
G/OR
Park/Neutral position
switch
[Ignition switch ON]
●
Gear position is Neutral
Approximately 0V
[Ignition switch ON]
●
Except the above gear position
BATTERY VOLTAGE
(11 - 14V)
EC-1240
[YD (WITH EURO-OBD)]
PNP SWITCH
Wiring Diagram
EBS013I3
YEC515A
PNP SWITCH
EC-1241
[YD (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
Diagnostic Procedure
EBS013I4
1.
CHECK OVERALL FUNCTION
With CONSULT-II
1.
Turn ignition switch ON.
2.
Select “P/N POSI SW” in “DATA MONITOR” mode with CON-
SULT-II.
3.
Check “P/N POSI SW” signal under the following conditions.
Without CONSULT-II
1.
Turn ignition switch ON.
2.
Check voltage between ECM terminal 110 and ground under the
following conditions.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 2.
2.
CHECK PNP SWITCH GROUND CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect park/neutral position (PNP) switch harness connec-
tor.
3.
Check harness continuity between PNP switch terminal 4
(YD22DDT engine models), 2 (YD22DDTi engine models) and
ground.
Refer to Wiring Diagram.
4.
Also check harness for short to power.
OK or NG
OK
>> GO TO 3.
NG
>> Repair open circuit or short to power in harness or connectors.
Shift lever position
P/N POSI SW
Neutral position
ON
Except the above position
OFF
SEF212Y
Shift lever position
Voltage
Neutral position
Approximately 0V
Except the above position
Battery voltage
PBIB1947E
Continuity should exist.
MBIB0873E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст