Nissan Almera Tino V10. Instruction — part 663
EC-1478
[YD (WITHOUT EURO-OBD)]
DTC P2135 APP SENSOR
On Board Diagnosis Logic
EBS0150G
The MI will not light up for this self-diagnosis.
DTC Confirmation Procedure
EBS0150H
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
WITH CONSULT-II
1.
Turn ignition switch ON.
2.
Select “DATA MONITOR” mode with CONSULT-II.
3.
Wait at least 5 seconds.
4.
Depress accelerator pedal slowly spending 5 seconds, and then
release it slowly spending 5 seconds.
5.
If DTC is detected, go to
EC-1480, "Diagnostic Procedure"
.
91
B
Accelerator pedal position
sensor 2
[Ignition switch ON]
●
Engine stopped
●
Accelerator pedal: Fully released
0.4 - 0.7V
[Ignition switch ON]
●
Engine stopped
●
Accelerator pedal: Fully depressed
2.2 - 2.7V
92
W
Accelerator pedal position
sensor 2 ground
[Ignition switch ON]
Approximately 0.3V
TERMI-
NAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA
(DC Voltage)
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P2135
Accelerator pedal position
sensor 1, 2 signal correlation
The correlation between APP sensor 1
signal and APP sensor 2 signal is out of
the normal range.
●
Harness or connectors
(The APP sensor circuit is open or shorted.)
●
Accelerator pedal position sensor
SEF817Y
DTC P2135 APP SENSOR
EC-1479
[YD (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
Wiring Diagram
EBS0150I
YEC521A
EC-1480
[YD (WITHOUT EURO-OBD)]
DTC P2135 APP SENSOR
Diagnostic Procedure
EBS0150J
1.
CHECK GROUND CONNECTIONS
1.
Turn ignition switch OFF.
2.
Loosen and retighten body ground screw. Refer to
.
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace ground connection.
2.
CHECK APP SENSOR POWER SUPPLY CIRCUIT
1.
Disconnect accelerator pedal position (APP) sensor harness
connector.
2.
Turn ignition switch ON.
3.
Check voltage between APP sensor terminals 1, 2 and ground
with CONSULT-II or tester.
OK or NG
OK
>> GO TO 3.
NG
>> Repair open circuit or short to ground or short to power
in harness or connectors.
3.
CHECK APP SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check harness continuity between APP sensor terminal 4 and ECM terminal 84, APP sensor terminal 5
and ECM terminal 92.
Refer to Wiring Diagram.
4.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 4.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
MBIB0915E
MBIB0904E
Voltage: Approximately 5.3V
PBIB0782E
Continuity should exist.
DTC P2135 APP SENSOR
EC-1481
[YD (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
4.
CHECK APP SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Check harness continuity between ECM terminal 83 and APP sensor terminal 3, ECM terminal 91 and
APP sensor terminal 6.
Refer to Wiring Diagram.
2.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 5.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
5.
CHECK APP SENSOR
Refer to
EC-1481, "Component Inspection"
.
OK or NG
OK
>> GO TO 6.
NG
>> Replace accelerator pedal assembly.
6.
CHECK INTERMITTENT INCIDENT
Refer to
EC-1309, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
.
>> INSPECTION END
Component Inspection
EBS0150K
ACCELERATOR PEDAL POSITION SENSOR
1.
Reconnect all harness connectors disconnected.
2.
Turn ignition switch ON.
3.
Check voltage between ECM terminals 83 (APP sensor 1 sig-
nal), 91 (APP sensor 2 signal) and body ground under the fol-
lowing conditions.
4.
If NG, replace accelerator pedal assembly.
Removal and Installation
EBS0150L
ACCELERATOR PEDAL
Refer to FE-16, “ACCELERATOR CONTROL SYSTEM”.
Continuity should exist.
Terminal
Accelerator pedal
Voltage
83
(Accelerator pedal position
sensor 1)
Fully released
0.5 - 1.0V
Fully depressed
4.2 - 5.2V
91
(Accelerator pedal position
sensor 2)
Fully released
0.4 - 0.7V
Fully depressed
2.2 - 2.7V
MBIB0615E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст