Nissan Almera Tino V10. Instruction — part 434
EC-562
[QG (WITHOUT EURO-OBD)]
PRECAUTIONS
●
Do not depress accelerator pedal when starting.
●
Immediately after starting, do not rev up engine unneces-
sarily.
●
Do not rev up engine just prior to shutdown.
●
When installing C.B. ham radio or a mobile phone, be sure
to observe the following as it may adversely affect elec-
tronic control systems depending on installation location.
–
Keep the antenna as far as possible from the electronic
control units.
–
Keep the antenna feeder line more than 20 cm (8 in) away
from the harness of electronic controls.
Do not let them run parallel for a long distance.
–
Adjust the antenna and feeder line so that the standing-
wave radio can be kept smaller.
–
Be sure to ground the radio to vehicle body.
●
Regarding V10 models with A/T, “B1” indicates bank 1 (cyl-
inders number 1 and 4), “B2” indicates bank 2 (cylinders
number 2 and 3).
Wiring Diagrams and Trouble Diagnosis
EBS00QUK
When you read wiring diagrams, refer to the following:
●
“HOW TO READ WIRING DIAGRAMS”, GI-11
●
“POWER SUPPLY ROUTING”, EL-11 for power distribution circuit
When you perform trouble diagnosis, refer to the following:
●
“How to Follow Test Groups in Trouble Diagnoses”, GI-32
●
“HOW TO PERFORM EFFICIENT DIAGNOSES FOR AN ELECTRICAL INCIDENT”, GI-21
SEF709Y
SEF708Y
SEF440Y
PREPARATION
EC-563
[QG (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
PREPARATION
PFP:00002
Special Service Tools
EBS00QUL
Commercial Service Tools
EBS00QUM
Tool number
Tool name
Description
KV10117100
Heated oxygen
sensor wrench
Loosening or tightening heated oxygen sensors
with 22 mm (0.87 in) hexagon nut
KV10114400
Heated oxygen
sensor wrench
Loosening or tightening heated oxygen sensors
a: 22 mm (0.87 in)
KV109E0010
Break-out box
Measuring ECM signals with a circuit tester
KV109E0080
Y-cable adapter
Measuring ECM signals with a circuit tester
S-NT379
S-NT636
S-NT825
S-NT826
Tool name
Description
Quick connector
release
Removing fuel tube quick connectors in engine
room
(Available in SEC. 164 of PARTS CATALOG: Part
No. 16441 6N210)
Fuel filler cap adapter
Checking fuel tank vacuum relief valve opening
pressure
PBIC0198E
S-NT653
EC-564
[QG (WITHOUT EURO-OBD)]
PREPARATION
Socket wrench
Removing and installing engine coolant
temperature sensor
Oxygen sensor thread
cleaner
ie: (J-43897-18)
(J-43897-12)
Reconditioning the exhaust system threads
before installing a new oxygen sensor. Use with
anti-seize lubricant shown below.
a: 18 mm diameter with pitch 1.5 mm for
Zirconia Oxygen Sensor
b: 12 mm diameter with pitch 1.25 mm for
Titania Oxygen Sensor
Anti-seize lubricant
ie: (Permatex
TM
133AR or equivalent
meeting MIL
specification MIL-A-
907)
Lubricating oxygen sensor thread cleaning tool
when reconditioning exhaust system threads.
Tool name
Description
S-NT705
AEM488
S-NT779
ENGINE CONTROL SYSTEM
EC-565
[QG (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
ENGINE CONTROL SYSTEM
PFP:23710
System Diagram - M/T Models
EBS00QUN
MBIB0239E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст