Nissan Almera Tino V10. Instruction — part 120
AT-204
[EURO-OBD]
DTC VEHICLE SPEED SENSOR MTR
Without CONSULT-II
1.
Start engine.
2.
Drive vehicle under the following conditions:
Selector lever in “D” and vehicle speed higher than 25 km/h (16 MPH).
3.
Perform self-diagnosis.
Refer to
AT-51, "TCM SELF-DIAGNOSTIC PROCEDURE (NO
.
4.
If DTC is detected, go to
AT-206, "Diagnostic Procedure"
.
MCIB9026E
DTC VEHICLE SPEED SENSOR MTR
AT-205
[EURO-OBD]
D
E
F
G
H
I
J
K
L
M
A
B
AT
Wiring Diagram — AT — VSSMTR
ECS00992
YAT385A
AT-206
[EURO-OBD]
DTC VEHICLE SPEED SENSOR MTR
Diagnostic Procedure
ECS00993
1.
CHECK INPUT SIGNAL
With CONSULT-II
1.
Start engine.
2.
Select “TCM INPUT SIGNALS” in “DATA MONITOR” mode for
“A/T” with CONSULT-II.
3.
Read out the value of “VHCL/S SE·MTR” while driving.
Check the value changes according to driving speed.
Without CONSULT-II
1.
Start engine.
2.
Check voltage between TCM terminal 40 and ground while driv-
ing at 2 to 3 km/h (1 to 2 MPH) for 1 m (3 ft) or more.
OK or NG
OK
>> GO TO 2
NG
>> Check the following items:
●
Vehicle speed sensor and ground circuit for vehicle
speed sensor
Refer to EL-110, “Trouble Diagnosis”.
●
Harness for short or open between TCM and vehicle speed sensor (Main harness)
2.
CHECK DTC
Perform
AT-203, "DIAGNOSTIC TROUBLE CODE (DTC) CONFIRMATION PROCEDURE"
.
OK or NG
OK
>> INSPECTION END
NG
>> 1. Perform TCM input/output signal inspection.
2. If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
SAT614J
Voltage:
Voltage varies between less than 1V and
more than 4.5V.
SCIA0717E
DTC CONTROL UNIT (RAM), CONTROL UNIT (ROM)
AT-207
[EURO-OBD]
D
E
F
G
H
I
J
K
L
M
A
B
AT
DTC CONTROL UNIT (RAM), CONTROL UNIT (ROM)
PFP:31036
Description
ECS00994
The TCM consists of a microcomputer and connectors for signal
input and output and for power supply. The unit controls the A/T.
ON BOARD DIAGNOSIS LOGIC
DIAGNOSTIC TROUBLE CODE (DTC) CONFIRMATION PROCEDURE
NOTE:
If “DIAGNOSTIC TROUBLE CODE CONFIRMATION PROCEDURE” has been previously conducted,
always turn ignition switch “OFF” and wait at least 5 seconds before conducting the next test.
With CONSULT-II
1.
Turn ignition switch “ON” and select “DATA MONITOR” mode for
A/T with CONSULT-II.
2.
Start engine.
3.
Run engine for at least 2 seconds at idle speed.
4.
If DTC is detected, go to
AT-208, "Diagnostic Procedure"
.
Without CONSULT-II
Follow the procedure “With CONSULT-II”.
SAT574J
Diagnostic Trouble Code No.
Malfunction is detected when.
Check Item (Possible Cause)
: CONTROL UNIT (RAM),
CONTROL UNIT (ROM)
TCM memory (RAM) or (ROM) is malfunc-
tioning.
●
TCM
SAT014K
SAT971J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст