Nissan Almera Tino V10. Instruction — part 854
EM-72
[QG]
ENGINE ASSEMBLY
19. Install lifting chain hooks into engine slinger and suspend engine with hoist.
20. Lift with hoist and secure the engine in position.
●
Use a instruction lift table caddy (commercial service tool) or
equivalently rigid tool such as a jack or trestle. Securely sup-
port bottom of engine and transaxle, and simultaneously
adjust hoist tension.
CAUTION:
●
Put a piece of wood or something similar as the sup-
porting surface, secure a completely stable condition.
21. Remove RH engine mounting insulator.
22. Pull LH engine mounting through-bolt out.
23. Remove mounting bolts at front and rear of center member.
24. Lower instruction lift table caddy (or raise lift), and remove engine
transaxle assembly from vehicle.
CAUTION:
●
When carrying out this work, be sure to check all parts
for interference with vehicle body.
●
Be sure to check that all the applicable connections have
been properly disconnected.
●
Be careful to prevent vehicle from dropping off the lift. Be
aware that changes in center of gravity may cause bal-
ance incidents.
Disassembly
●
The following shows engine and transaxle disassembly on level ground.
CAUTION:
During disassembly, always support bottom with a wooden block. Suspend engine slinger with a
hoist. Be sure to check safety of work at any time.
25. Remove center member.
26. Remove engine mounting insulators and bracket.
27. Remove stater motor. Refer to SC-13, “Starting System”.
28. Separate engine and transaxle.
INSTALLATION
Install in the reverse order of removal.
●
Do not allow oil to get on mounting insulator. Be careful not to damage mounting insulator.
●
When installation directions are specified, install parts according to the direction marks on them referring
to components illustration.
●
Make sure that each mounting insulator is seated properly, and tighten mounting bolts and nuts.
INSPECTION AFTER INSTALLATION
●
Before starting engine, check the levels of coolant, lubrications and working oils. If less than required
quantity, fill to the specified level.
MBIA0041E
PBIC0583E
KBIA0227J
ENGINE ASSEMBLY
EM-73
[QG]
C
D
E
F
G
H
I
J
K
L
M
A
EM
●
Use procedure below to check for fuel leakage.
a. Turn ignition switch ON (with engine stopped). With fuel pressure applied to fuel piping, check for fuel
leakage at connection points.
b. Start engine. With engine speed increased, check again for fuel leakage at connection points.
●
Run engine to check for unusual noise and vibration.
●
Warm up engine thoroughly to make sure there is no leakage of coolant, lubricants, working oil, fuel and
exhaust gas.
●
Bleed air from passages in pipes and tubes of applicable lines, such as in cooling system.
●
After cooling down engine, again check amounts of coolant, lubricants, oil, and fluid. Refill to specified
level, if necessary.
EM-74
[QG]
CYLINDER BLOCK
CYLINDER BLOCK
PFP:11010
Disassembly and Assembly
EBS00QES
MBIA0042E
CYLINDER BLOCK
EM-75
[QG]
C
D
E
F
G
H
I
J
K
L
M
A
EM
CAUTION:
Apply new engine oil to parts marked in illustration before installation.
DISASSEMBLY
1.
Remove engine and transaxle assembly from vehicle, and separate transaxle from engine. Refer to
70, "Removal and Installation"
.
2.
Mount engine on an engine stand with the following procedure.
a.
Remove exhaust manifold and catalytic converter. Refer to
EM-21, "Removal and Installation"
.
b.
Remove engine front mounting bracket, alternator and air compressor bracket.
c.
Install engine sub-attachment to left side of cylinder block.
d.
Lift engine, and mount it onto the engine stand.
1.
Rear oil seal
2.
Rear oil seal retainer
3.
Crankshaft position sensor (POS)
4.
O-ring
5.
Knock sensor
6.
Oil level gauge guide
7.
Cylinder block
8.
Thrust bearing
9.
Main bearing
10. Crankshaft
11. Key
12. Top ring
13. 2nd ring
14. Oil ring
15. Main bearing
16. Piston
17. Snap ring
18. Piston pin
19. Connecting rod
20. Connecting rod bearing
21. Connecting rod cap
22. Connecting rod nut
23. Main bearing cap bolt
24. Baffle plate
25. Main bearing cap
26. Signal plate
27. Rear plate
28. Coolant drain plug
29. Flywheel (M/T models)
30. Drive plate (A/T models)
PBIC0585E
PBIC1017E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст