Nissan Almera Tino V10. Instruction — part 150
AT-324
[EXC.F/EURO-OBD]
TROUBLE DIAGNOSES FOR SYMPTOMS
9. A/T Does Not Shift: D
1
→
D
2
Or Does Not Kick down: D
4
→
D
2
ECS009AF
SYMPTOM:
A/T does not shift from D
1
to D
2
at the specified speed.
A/T does not shift from D
4
to D
2
when depressing accelerator pedal fully at the specified speed.
1.
CHECK SYMPTOM
Are 7. Vehicle Does Not Creep Forward In “D”, “2” Or “1” Position and 8. Vehicle Cannot Be Started From D
1
OK?
Yes or No
Yes
>> GO TO 2
No
>> Go to
AT-320, "7. Vehicle Does Not Creep Forward In “D”, “2” Or “1” Position"
,
.
2.
CHECK PNP SWITCH CIRCUIT
With CONSULT-II
Does “TCM INPUT SIGNALS” in “DATA MONITOR” show damage to PNP switch circuit?
Without CONSULT-II
Does self-diagnosis show damage to PNP switch circuit?
Yes or No
Yes
>> Check PNP switch circuit. Refer to
.
No
>> GO TO 3
3.
CHECK VEHICLE SPEED SENSOR·A/T (REVOLUTION SENSOR) AND CHECK VEHICLE SPEED
SENSOR·MTR CIRCUIT
Check vehicle speed sensor·A/T (revolution sensor) and vehicle speed sensor·MTR circuit. Refer to
"VEHICLE SPEED SENSOR - A/T (REVOLUTION SENSOR)"
and
AT-352, "DTC VEHICLE SPEED SEN-
.
OK or NG
OK
>> GO TO 4
NG
>> Repair or replace vehicle speed sensor·A/T (revolution sensor) and vehicle speed sensor·MTR
circuits.
4.
CHECK THROTTLE POSITION SENSOR*
*: This sensor means accelerator pedal position (APP) sensor.
Refer to
AT-356, "ACCELE RATOR PEDAL POSITION (APP) SEN-
.
OK or NG
OK
>> GO TO 5
NG
>> Repair or replace accelerator pedal position (APP) sen-
sor.
SCIA0706E
MCIA0096E
TROUBLE DIAGNOSES FOR SYMPTOMS
AT-325
[EXC.F/EURO-OBD]
D
E
F
G
H
I
J
K
L
M
A
B
AT
5.
CHECK A/T FLUID CONIDITION
1.
Remove oil pan, refer to
.
2.
Check A/T fluid condition.
OK or NG
OK
>> GO TO 6
NG
>> GO TO 8
6.
DETECT MALFUNCTIONING ITEM
1.
Remove control valve. Refer to
AT-410, "Control Valve Assembly and Accumulators"
.
2.
Check the following items:
–
Shift valve A
–
Shift solenoid valve A (
AT-361, "SHIFT SOLENOID VALVE A"
)
–
Pilot valve
–
Pilot filter
OK or NG
OK
>> GO TO 7
NG
>> Repair or replace damaged parts.
7.
CHECK SYMPTOM
Check again.
OK or NG
OK
>> INSPECTION END
NG
>> 1. Perform TCM input/output signal inspection.
2. If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
8.
DETECT MALFUNCTIONING ITEM
1.
Remove control valve. Refer to
AT-410, "Control Valve Assembly and Accumulators"
.
2.
Check the following items:
–
Shift valve A
–
Shift solenoid valve A (
AT-361, "SHIFT SOLENOID VALVE A"
)
–
Pilot valve
–
Pilot filter
3.
Disassemble A/T.
4.
Check the following items:
–
Servo piston assembly
–
Brake band
–
Oil pump assembly
OK or NG
OK
>> GO TO 7
NG
>> Repair or replace damaged parts.
SAT171B
AT-326
[EXC.F/EURO-OBD]
TROUBLE DIAGNOSES FOR SYMPTOMS
10. A/T Does Not Shift: D
2
→
D
3
ECS009AG
SYMPTOM:
A/T does not shift from D
2
to D
3
at the specified speed.
1.
CHECK SYMPTOM
Are 7. Vehicle Does Not Creep Forward In “D”, “2” Or “1” Position and 8. Vehicle Cannot Be Started From D
1
OK?
Yes or No
Yes
>> GO TO 2
No
>> Go to
AT-320, "7. Vehicle Does Not Creep Forward In “D”, “2” Or “1” Position"
,
.
2.
CHECK PNP SWITCH CIRCUIT
With CONSULT-II
Does “TCM INPUT SIGNALS” in “DATA MONITOR” show damage to PNP switch circuit?
Without CONSULT-II
Does self-diagnosis show damage to PNP switch circuit?
Yes or No
Yes
>> Check PNP switch circuit. Refer to
.
No
>> GO TO 3
3.
CHECK THROTTLE POSITION SENSOR*
*: This sensor means accelerator pedal position (APP) sensor.
Refer to
AT-356, "ACCELE RATOR PEDAL POSITION (APP) SEN-
.
OK or NG
OK
>> GO TO 4
NG
>> Repair or replace throttle position sensor.
4.
CHECK A/T FLUID CONDITION
1.
Remove oil pan, refer to
.
2.
Check A/T fluid condition.
OK or NG
OK
>> GO TO 5
NG
>> GO TO 7
SCIA0706E
MCIA0096E
SAT171B
TROUBLE DIAGNOSES FOR SYMPTOMS
AT-327
[EXC.F/EURO-OBD]
D
E
F
G
H
I
J
K
L
M
A
B
AT
5.
DETECT MALFUNCTIONING ITEM
1.
Remove control valve assembly. Refer to
AT-410, "Control Valve Assembly and Accumulators"
.
2.
Check the following items:
–
Shift valve B
–
Shift solenoid valve B (
AT-366, "SHIFT SOLENOID VALVE B"
)
–
Pilot valve
–
Pilot filter
OK or NG
OK
>> GO TO 6
NG
>> Repair or replace damaged parts.
6.
CHECK SYMPTOM
Check again.
OK or NG
OK
>> INSPECTION END
NG
>> 1. Perform TCM input/output signal inspection.
2. If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
7.
DETECT MALFUNCTIONING ITEM
1.
Remove control valve assembly. Refer to
AT-410, "Control Valve Assembly and Accumulators"
.
2.
Check the following items:
–
Shift valve B
–
Shift solenoid valve B (
AT-366, "SHIFT SOLENOID VALVE B"
)
–
Pilot valve
–
Pilot filter
3.
Disassemble A/T.
4.
Check the following items:
–
Servo piston assembly
–
High clutch assembly
–
Oil pump assembly
OK or NG
OK
>> GO TO 6
NG
>> Repair or replace damaged parts.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст