Nissan Almera Tino V10. Instruction — part 675
EC-1526
[YD (WITHOUT EURO-OBD)]
START SIGNAL
START SIGNAL
PFP:48750
Wiring Diagram
EBS01526
YEC516A
START SIGNAL
EC-1527
[YD (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
Diagnostic Procedure
EBS01527
1.
CHECK START SIGNAL OVERALL FUNCTION
With CONSULT-II
1.
Turn ignition switch ON.
2.
Check “START SIGNAL” in “DATA MONITOR” mode with CON-
SULT-II under the following conditions.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 2.
2.
CHECK START SIGNAL INPUT SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector and ignition switch harness connector.
3.
Check harness continuity between ECM terminal 99 and ignition switch terminal 6.
Refer to Wiring Diagram.
4.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 3.
3.
DETECT MALFUNCTIONING PART
Check the following.
●
10A fuse
●
Fuse block (J/B) connectors M2, E109
●
Harness for open or short between ECM and ignition switch
>> Repair open circuit or short to ground or short to power in harness or connectors.
4.
CHECK INTERMITTENT INCIDENT
Refer to
EC-1309, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
.
>> INSPECTION END
Condition
START SIGNAL
Ignition switch ON
OFF
Ignition switch START
ON
PBIB0433E
Continuity should exist.
EC-1528
[YD (WITHOUT EURO-OBD)]
MI & DATA LINK CONNECTORS
MI & DATA LINK CONNECTORS
PFP:24814
Wiring Diagram
EBS01528
TBWA0585E
SERVICE DATA AND SPECIFICATIONS (SDS)
EC-1529
[YD (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
SERVICE DATA AND SPECIFICATIONS (SDS)
PFP:00100
General Specifications
EBS01529
Mass Air Flow Sensor
EBS0152A
Engine Coolant Temperature Sensor
EBS0152B
Fuel Rail Pressure Sensor
EBS0152C
Glow Plug
EBS0152D
EGR Volume Control Valve
EBS0152E
Crankshaft Position Sensor
EBS0152F
Refer to
EC-1400, "Component Inspection"
.
Camshaft Position Sensor
EBS0152G
Refer to
EC-1411, "Component Inspection"
.
Engine
YD22DDT/YD22DDTi
Idle speed
725
±
25 rpm
Maximum engine speed
4,900 rpm
Supply voltage
Battery voltage (11 - 14V)
Ignition switch ON (Engine stopped.)
Approx. 0.4V
Idle (Engine is warmed up to normal operating temperature.)
1.5 - 2.0V
2,000 rpm (Engine is warmed up to normal operating tempera-
ture.)
2.2 - 2.7V
Temperature
°
C (
°
F)
Resistance k
Ω
20 (68)
2.1 - 2.9
50 (122)
0.68 - 1.00
90 (194)
0.236 - 0.260
Supply voltage
Approximately 5V
Idle (Engine is warmed up to normal operating temperature.)
1.7 - 2.0V
2,000 rpm (Engine is warmed up to normal operating tempera-
ture.)
2.0 - 2.3V
Resistance [at 25
°
C (77
°
F)]
Ω
Approximately 0.8
Resistance [at 25
°
C (77
°
F)]
Ω
13 - 17
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст