Nissan Almera Tino V10. Instruction — part 516
EC-890
[QG (WITHOUT EURO-OBD)]
EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
Component Inspection
EBS00R33
EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
With CONSULT-II
Check air passage continuity of EVAP canister purge volume control
solenoid valve under the following conditions.
Without CONSULT-II
Check air passage continuity of EVAP canister purge volume control
solenoid valve under the following conditions.
Removal and Installation
EBS00R34
EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
Refer to
.
Condition
(PURG VOL CONT/V value)
Air passage continuity
between A and B
100%
Yes
0%
No
PBIB0149E
Condition
Air passage continuity
between A and B
12V direct current supply between
terminals 1 and 2
Yes
No supply
No
PBIB0150E
VSS
EC-891
[QG (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
VSS
PFP:32702
Description
EBS00R35
NOTE:
If DTC U1000 or U1001 is displayed, first perform the trouble diagnosis for DTC U1000, U1001. Refer to
EC-651, "DTC U1000, U1001 CAN COMMUNICATION LINE"
.
The vehicle speed signal is sent to the combination meter from ABS actuator and electric unit (control unit)
through CAN communication line. The combination meter then sends a signal to the ECM through CAN com-
munication line.
Diagnostic Procedure
EBS00R36
1.
CHECK VEHICLE SPEED SIGNAL OVERALL FUNCTION
With CONSULT-II
1.
Lift up the vehicle.
2.
Start engine.
3.
Select “VHCL SPEED SE” in “DATA MONITOR” mode with
CONSULT-II.
4.
Make sure that “VHCL SPEED SE” indication exceeds 10 km/h
(6 MPH) when rotating wheels with suitable gear position.
Without CONSULT-II
1.
Lift up the vehicle.
2.
Start engine.
3.
Read vehicle speed with combination meter.
Make sure that vehicle speed indication exceeds 10 km/h (6 MPH) when rotating wheels with suitable
gear position.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 2.
2.
CHECK DTC WITH ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Check DTC with ABS actuator and electric unit (control unit), Refer to “TROUBLEDIAGNOSIS-BASIC
INSPECTION”, BR-70.
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace.
3.
CHECK COMBINATION METER
Check combination meter function.
Refer to “METERS AND GAUGES”, EL-100.
>> INSPECTION END
SEF196Y
EC-892
[QG (WITHOUT EURO-OBD)]
POWER STEERING PRESSURE SENSOR
POWER STEERING PRESSURE SENSOR
PFP:49763
Component Description
EBS00R37
Power steering pressure (PSP) sensor is installed to the power
steering high-pressure tube and detects a power steering load. This
sensor is a potentiometer which transforms the power steering load
into output voltage, and emits the voltage signal to the ECM. The
ECM controls the electric throttle control actuator and adjusts the
throttle valve opening angle to increase the engine speed and
adjusts the idle speed for the increased load.
CONSULT-II Reference Value in Data Monitor Mode
EBS00R38
Specification data are reference values.
MBIB1006E
MONITOR ITEM
CONDITION
SPECIFICATION
PW/ST SIGNAL
●
Engine: After warming up, idle
the engine
Steering wheel is in neutral position.
(Forward direction)
OFF
Steering wheel is turned.
ON
POWER STEERING PRESSURE SENSOR
EC-893
[QG (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
Wiring Diagram
EBS00R39
YEC628A
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст