Nissan Almera Tino V10. Instruction — part 97
AT-112
[EURO-OBD]
CAN COMMUNICATION
ABS operation signal
T
R
OD OFF switch signal
R
T
OD OFF indicator signal
T
R
A/T self-diagnosis signal
R
T
ABS warning lamp signal
T
R
N range switch signal
R
T
P range switch signal
R
T
Signals
ECM
TCM
ABS actuator
and electric
unit (control
unit)
Smart entrance
control unit
Combination
meter
DTC P0705 PARK/NEUTRAL POSITION (PNP) SWITCH
AT-113
[EURO-OBD]
D
E
F
G
H
I
J
K
L
M
A
B
AT
DTC P0705 PARK/NEUTRAL POSITION (PNP) SWITCH
PFP:32006
Description
ECS0097B
●
The PNP switch assembly includes a transmission range switch.
●
The transmission range switch detects the selector lever posi-
tion and sends a signal to the TCM.
TCM TERMINALS AND REFERENCE VALUE
Remarks: Specification data are reference values.
ON BOARD DIAGNOSIS LOGIC
DIAGNOSTIC TROUBLE CODE (DTC) CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DIAGNOSTIC TROUBLE CODE CONFIRMATION PROCEDURE” has been previously conducted,
always turn ignition switch “OFF” and wait at least 5 seconds before conducting the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
SCIA0752E
Termi-
nal No.
Wire color
Item
Condition
Judgement stan-
dard
(Approx.)
26
BR/Y
PNP switch “1”
position
and
When setting selector lever to “1”
position.
Battery voltage
When setting selector lever to other
positions.
0V
27
L
PNP switch “2”
position
When setting selector lever to “2”
position.
Battery voltage
When setting selector lever to other
positions.
0V
34
W/G
PNP switch “D”
position
When setting selector lever to “D”
position.
Battery voltage
When setting selector lever to other
positions.
0V
35
G/W
PNP switch “R”
position
When setting selector lever to “R”
position.
Battery voltage
When setting selector lever to other
positions.
0V
36
G
PNP switch “N” or
“P” position
When setting selector lever to “N” or
“P” position.
Battery voltage
When setting selector lever to other
positions.
0V
Diagnostic trouble code
Malfunction is detected when...
Check items (Possible cause)
: PNP SW/CIRC
TCM does not receive the correct voltage
signal from the switch based on the gear
position.
●
Harness or connectors
(The PNP switch circuit is open or
shorted.)
●
PNP switch
: P0705
AT-114
[EURO-OBD]
DTC P0705 PARK/NEUTRAL POSITION (PNP) SWITCH
With CONSULT-II
1.
Turn ignition switch “ON”.
2.
Select “DATA MONITOR” mode for “ENGINE” with CONSULT-II.
3.
Start engine and maintain the following conditions for at least 5
consecutive seconds.
VHCL SPEED SE: 10 km/h (6 MPH) or more
THRTL POS SEN: More than 1.3V
Selector lever: D position (OD “ON” or “OFF”)
4.
If DTC is detected, go to
AT-116, "Diagnostic Procedure"
.
With GST
Follow the procedure “With CONSULT-II”.
SAT014K
SAT020K
DTC P0705 PARK/NEUTRAL POSITION (PNP) SWITCH
AT-115
[EURO-OBD]
D
E
F
G
H
I
J
K
L
M
A
B
AT
Wiring Diagram — AT — PNP/SW
ECS0097C
YAT369A
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст