Nissan Almera Tino V10. Instruction — part 767
DIAGNOSTIC PROCEDURE 3
NLEL0589S07
Self-diagnostic results:
“DIFFERENCE OF KEY” displayed on CONSULT-II screen
1
CONFIRM SELF-DIAGNOSTIC RESULTS
Confirm SELF-DIAGNOSTIC RESULTS “DIFFERENCE OF KEY” displayed on CONSULT-II screen.
SEL367X
Is CONSULT-II screen displayed as above?
Yes
©
GO TO 2.
No
©
GO TO EL-359, “SYMPTOM MATRIX CHART 1”.
2
PERFORM INITIALIZATION WITH CONSULT-II
Perform initialization with CONSULT-II. Re-register all NATS ignition key IDs.
For initialization and registration of NATS ignition key IDs, refer to “CONSULT-II operation instruction NATS”.
NOTE:
If the initialization is not completed or fails, CONSULT-II shows above message on the screen.
SEL297W
Can the system be initialized and can the engine be started with re-registered NATS ignition key?
Yes
©
I
Ignition key ID was unregistered. Ref. part No. D
No
©
I
IMMU (Smart entrance control unit) is malfunctioning.
I
Replace IMMU (Smart entrance control unit). Ref. part No. A
I
Perform initialization with CONSULT-II.
For initialization, refer to “CONSULT-II operation instruction NATS”.
NATS (NISSAN ANTI-THEFT SYSTEM)
Trouble Diagnoses (Cont’d)
EL-364
DIAGNOSTIC PROCEDURE 4
=NLEL0589S08
Self-diagnostic results:
“CHAIN OF IMMU-KEY” displayed on CONSULT-II screen
1
CONFIRM SELF-DIAGNOSTIC RESULTS
Confirm SELF-DIAGNOSTIC RESULTS “CHAIN OF IMMU-KEY” displayed on CONSULT-II screen.
SEL957W
Is CONSULT-II screen displayed as above?
Yes
©
GO TO 2.
No
©
GO TO EL-359, “SYMPTOM MATRIX CHART 1”.
2
CHECK NATS ANTENNA AMP. INSTALLATION
Check NATS antenna amp. installation. Refer to EL-374, “How to Replace NATS Antenna Amp”.
OK or NG
Yes
©
GO TO 3.
No
©
Reinstall NATS antenna amp. correctly.
3
CHECK NATS IGNITION KEY ID CHIP
Start engine with another registered NATS ignition key.
Does the engine start?
Yes
©
I
Ignition key ID chip is malfunctioning.
I
Replace the ignition key.
I
Ref. part No. E5
I
Perform initialization with CONSULT-II.
I
For initialization, refer to “CONSULT-II Operation Instruction NATS”.
No
©
GO TO 4.
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
NATS (NISSAN ANTI-THEFT SYSTEM)
Trouble Diagnoses (Cont’d)
EL-365
4
CHECK POWER SUPPLY FOR NATS ANTENNA AMP.
Check voltage between NATS antenna amp. harness connector M29 terminal 1 (G) and ground with analogue tester.
SIIA1670E
Before turning ignition switch “ON”
Voltage: 0V
Just after turning ignition switch “ON”:
Pointer of tester should move.
OK or NG
OK
©
GO TO 5.
NG
©
I
Check harness for open or short between NATS antenna amp and IMMU (Smart
entrance control unit).
NOTE:
If harness is OK, replace IMMU (Smart entrance control unit), perform initialization
with CONSULT-II. For initialization, refer to “CONSULT-II operation instruction NATS”.
5
CHECK NATS ANTENNA AMP. SIGNAL LINE-1
Check voltage between NATS antenna amp. harness connector M29 terminal 3 (G/W) and ground with analogue tester.
SIIA1671E
Before turning ignition switch “ON”
Voltage: 0V
Just after turning ignition switch “ON”:
Pointer of tester should move.
OK or NG
OK
©
GO TO 6.
NG
©
I
Check harness for open or short between NATS antenna amp and IMMU (Smart
entrance control unit).
NOTE:
If harness is OK, replace IMMU (Smart entrance control unit), perform initialization
with CONSULT-II. For initialization, refer to “CONSULT-II operation instruction NATS”.
NATS (NISSAN ANTI-THEFT SYSTEM)
Trouble Diagnoses (Cont’d)
EL-366
6
CHECK NATS ANTENNA AMP. SIGNAL LINE-2
Check voltage between NATS antenna amp. harness connector M29 terminal 7 (Y/G) and ground with analogue tester.
SIIA1672E
Before turning ignition switch “ON”
Voltage: 0V
Just after turning ignition switch “ON”:
Pointer of tester should move.
OK or NG
OK
©
GO TO 7.
NG
©
I
Check harness for open or short between NATS antenna amp and IMMU (Smart
entrance control unit).
NOTE:
If harness is OK, replace IMMU (Smart entrance control unit), perform initialization
with CONSULT-II. For initialization, refer to “CONSULT-II operation instruction NATS”.
7
CHECK NATS ANTENNA AMP. GROUND LINE CIRCUIT
1. Turn ignition switch “OFF”
2. Disconnect NATS antenna amp connector.
3. Check continuity between NATS antenna amp. harness connector M29 terminal 5 (G/OR) and ground.
SIIA1673E
Continuity should exist.
OK or NG
OK
©
I
NATS antenna amp. malfunctioning.
Ref. part No. E6
NG
©
I
Check harness for open or short between NATS antenna amp and IMMU (Smart
entrance control unit).
NOTE:
If harness is OK, replace IMMU (Smart entrance control unit), perform initialization
with CONSULT-II. For initialization, refer to “CONSULT-II operation instruction NATS”.
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
NATS (NISSAN ANTI-THEFT SYSTEM)
Trouble Diagnoses (Cont’d)
EL-367
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст