Nissan Almera Tino V10. Instruction — part 187
AT-472
[ALL]
REPAIR FOR COMPONENT PARTS
3.
Install forward clutch piston assembly on forward clutch drum by
turning it slowly.
●
Apply ATF to inner surface of drum.
4.
Align notch in forward clutch piston with groove in forward clutch
drum.
5.
Install return spring on piston.
6.
Install spring retainer on return springs.
7.
Set Tool on spring retainer and install snap ring while compress-
ing return springs.
●
Set Tool directly over return springs.
●
Do not align snap ring gap with spring retainer stopper.
SAT216D
SAT217D
SAT218D
AAT685
SAT220D
REPAIR FOR COMPONENT PARTS
AT-473
[ALL]
D
E
F
G
H
I
J
K
L
M
A
B
AT
8.
Install drive plates, driven plates, retaining plate and dish plate
for overrun clutch.
●
Take care with order of plates.
9.
Install snap ring for overrun clutch.
10. Measure clearance between overrun clutch retaining plate and
snap ring.
If not within allowable limit, select proper retaining plate.
11. Install drive plates, driven plates, retaining plate and dish plate
for forward clutch.
●
Take care with order and direction of plates.
12. Install snap ring for forward clutch.
13. Measure clearance between forward clutch retaining plate and
snap ring.
If not within allowable limit, select proper retaining plate.
14. Check operation of forward clutch.
Refer to
AT-468, "Forward and Overrun Clutches"
.
SAT204D
Specified clearance:
Standard 1.0 - 1.4 mm (0.039 - 0.055 in)
Allowable limit 2.0 mm (0.079 in)
Overrun clutch retaining plate:
Refer to
AT-519, "SERVICE DATA AND SPECIFICA-
.
SAT227D
SAT203D
Specified clearance:
Standard 0.45 - 0.85 mm (0.0177 - 0.0335 in)
Allowable limit 1.85 mm (0.0728 in)
Forward clutch retaining plate:
Refer to
AT-519, "SERVICE DATA AND SPECIFICA-
.
SAT228D
SAT201D
AT-474
[ALL]
REPAIR FOR COMPONENT PARTS
15. Check operation of overrun clutch.
Refer to
AT-468, "Forward and Overrun Clutches"
.
Low & Reverse Brake
ECS009CP
COMPONENTS
DISASSEMBLY
1.
Check operation of low & reverse brake.
a.
Apply compressed air to oil hole of transmission case.
b.
Check to see that retaining plate moves to snap ring.
c.
If retaining plate does not contact snap ring:
●
D-ring might be damaged.
●
Oil seal might be damaged.
●
Fluid might be leaking past piston check ball.
2.
Stand transmission case.
3.
Remove snap ring.
4.
Remove drive plates, driven plates, retaining plate from trans-
mission case.
SAT202D
SAT486JA
SAT230D
SAT231D
REPAIR FOR COMPONENT PARTS
AT-475
[ALL]
D
E
F
G
H
I
J
K
L
M
A
B
AT
5.
Set Tool on spring retainer and remove snap ring while com-
pressing return springs.
●
Set Tool directly above return springs.
●
Do not expand snap ring excessively.
6.
Remove spring retainer and return springs.
●
Do not remove return springs from spring retainer.
7.
Apply compressed air to oil hole of transmission case while
holding piston.
8.
Remove piston from transmission case by turning it.
9.
Remove D-ring and oil seal from piston.
AAT687
SAT303E
SAT234D
SAT767G
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст