Nissan Almera Tino V10. Instruction — part 895
LIQUID GASKET APPLICATION PROCEDURE
. . ..32
Preparation . . . . . . . . . . . . . . . . 32
. . . . . . . . . ..32
Cooling Circuit . . . . . . . . . . . . . . ...33
System Check. . . . . . . . . . . . . . . 34
. . . . ...34
. . . . . . . . . . . 34
. . . . . . . . . 34
CHECKING COOLING SYSTEM FOR LEAKS
. . . 35
Water Pump . . . . . . . . . . . . . . . ...35
. . . . . . . ...35
. . . . . . . . . . . . . . . ...36
. . . . . . . . . . . . . . ...36
. . . . . . . . . . . . . . 36
Thermostat. . . . . . . . . . . . . . . . .37
. . . . . . . ...37
. . . . . . . . . . . . . . ...38
Radiator . . . . . . . . . . . . . . . . . .39
. . . . . . . . . . . . . ...39
. . . . . . . ...39
Cooling Fan . . . . . . . . . . . . . . . ...40
. . . . . . . . . . . . . ...40
. . . . . . . . . . . . 40
Changing Engine Coolant. . . . . . . . . . ..40
. . . . . . . 40
. . . . . . ...41
Overheating Cause Analysis . . . . . . . . . .42
Service Data and Specifications (SDS). . . . . .43
. . . . . . . . . . . . . . 43
. . . . . . . . . . . . . . . ..43
. . . . . . . . 43
CONTENTS
(Cont’d)
LC-2
SEM164F
AEM080
Precautions
LIQUID GASKET APPLICATION PROCEDURE
NLLC0001
1.
Use a scraper to remove all traces of old liquid gasket from
mating surfaces and grooves. Also, completely clean any oil
from these areas.
2.
Apply a continuous bead of liquid gasket to mating surfaces.
(Use Genuine Liquid Gasket or equivalent.)
I
For oil pan, be sure liquid gasket diameter is 3.5 to 4.5 mm
(0.138 to 0.177 in).
I
For areas except oil pan, be sure liquid gasket diameter is 2.0
to 3.0 mm (0.079 to 0.118 in).
3.
Apply liquid gasket around the inner side of bolt holes (unless
otherwise specified).
4.
Assembly should be done within 5 minutes after coating.
5.
Wait at least 30 minutes before refilling engine oil and engine
coolant.
Preparation
SPECIAL SERVICE TOOLS
NLLC0002
Tool number
Tool name
Description
ST25051001
Oil pressure gauge
NT050
Measuring oil pressure
ST25052000
Hose
NT559
Adapting oil pressure gauge to cylinder block
KV10115801
Oil filter wrench
NT772
Removing oil filter
WS39930000
Tube presser
NT052
Pressing the tube of liquid gasket
GI
MA
EM
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ENGINE LUBRICATION SYSTEM
QG
Precautions
LC-3
Lubrication Circuit
NLLC0003
SEM852FB
SLC339B
ENGINE LUBRICATION SYSTEM
QG
Lubrication Circuit
LC-4
SEM853F
Oil Pressure Check
NLLC0004
WARNING:
I
Be careful not to burn yourself, as the engine and oil may
be hot.
I
For M/T models, put gearshift lever in Neutral “N” posi-
tion.
1.
Check oil level.
2.
Remove oil pressure switch.
SLC926-A
3.
Install pressure gauge.
4.
Start engine and warm it up to normal operating temperature.
5.
Check oil pressure with engine running under no-load.
Engine speed
rpm
Approximate discharge pressure
kPa (bar, kg/cm
2
, psi)
600
More than 98 (0.98, 1.0, 14)
2,000
More than 294 (2.94, 3.0, 43)
6,000
More than 392 (3.92, 4.0, 57)
I
If difference is extreme, check oil passage and oil pump
for oil leaks.
6.
Install oil pressure switch with sealant.
: 13 - 17 N·m (1.25 - 1.75 kg-m, 9 - 12 ft-lb)
Oil Pump
REMOVAL AND INSTALLATION
NLLC0005
I
Make sure that O-ring is fitted properly.
1.
Drain engine oil.
2.
Remove drive belts.
3.
Remove oil pan. Refer to EM-25, “OIL PAN AND OIL
STRAINER”.
4.
Remove oil strainer.
5.
Remove front cover. Refer to EM-50, “TIMING CHAIN”.
6.
Install front cover.
7.
Reinstall parts in reverse order of removal.
GI
MA
EM
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ENGINE LUBRICATION SYSTEM
QG
Oil Pressure Check
LC-5
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст