Nissan Almera Tino V10. Instruction — part 5
SFA395
7.
Lock new larger and smaller boot bands securely with a suit-
able tool.
SFA800
Transaxle Side (TS79C, T79C, GI2300I & GI3300I)
NLAX0019S05
1.
Install boot and new small boot band on drive shaft.
Cover drive shaft serration with tape so as not to damage boot
during installation.
SFA612
2.
Install spider assembly securely, making sure the marks which
were made during disassembly are properly aligned.
3.
Install new snap ring.
NAX005
4.
Pack drive shaft with specified amount of grease.
Specified amount of grease:
Refer to AX-19, SDS.
5.
Install slide joint housing.
6.
Set boot so that it does not swell and deform when its length
is “L
2
”:
Refer to AX-19, SDS.
SFA395
Make sure that the boot is properly installed on the drive shaft
groove.
7.
Lock new larger and smaller boot bands.
I
Boot bands type A
a)
Lock new larger and smaller boot bands securely with a suit-
able tool.
GI
MA
EM
LC
EC
FE
CL
MT
AT
SU
BR
ST
RS
BT
HA
SC
EL
IDX
FRONT AXLE
Drive Shaft (Cont’d)
AX-17
SDIA0876J
I
Boot bands type B
a)
As shown in the figure, secure the big and small ends of the
boot with new boot bands.
YAX011
b)
Rotate joint part and confirm that mounting position of boot
does not deviate. When it deviates, mount a new boot band
again.
CAUTION:
When fixing boot band, fix so that the diameter “M” on the
figure becomes as follows.
Diameter “M”: 5 mm (0.20 in)
SFA618
Support Bearing
NLAX0019S04
I
Press bearing into retainer.
SFA694
I
Press drive shaft into bearing.
SFA444B
I
Install snap ring.
I
Install new dust shield.
FRONT AXLE
Drive Shaft (Cont’d)
AX-18
Service Data and Specifications (SDS)
DRIVE SHAFT
=NLAX0020
QG
YD
M/T models
A/T models
5 M/T models
6 M/T models
LH
RH
Joint type
Transaxle side
GI2300I
T79C
TS79C
D90
GI3300I
Grease
Quality
39709-BM500
39709-2U600
39709-BM500
*2
Joint type
Wheel side
AC2300I
ZF90
B90
AC3300I
Grease
Quality
Nissan genuine
grease or equiva-
lent
39209-2U600
Nissan genuine
grease or equiva-
lent
*3
Grease
Capacity
g (oz)
Transaxle side
125.5 - 135.5
(4.42 - 4.77)
155 - 165
(5.47 - 5.82)
145 - 165
(5.11 - 5.82)
167 - 177
(5.89 - 6.24)
Wheel side
40 - 50
(1.41 - 1.76)
115 - 125
(4.06 - 4.41)
93 - 103
(3.28 - 3.63)
120 - 140
(4.41 - 4.94)
110 - 130
(3.88 - 4.59)*4
Boot length
mm (in)
Transaxle side “L
2
”
98 - 100
(3.86 - 3.94)*1
101.5 - 103.5
(4.00 - 4.07)*1
98 (3.86)*1
*1
Wheel side “L
1
”
94 - 96
(3.70 - 3.78)*1
94.1 - 96.1
(3.705 - 3.783)*1
110 (4.33)
*1
SFA961AA
SFA962A
*1: Fit boot to boot groove in bar shaft
*2: GKN-ONE LUBER C grease or Nissan genuine grease or equivalent
*3: GKN HTBJ grease or Nissan genuine grease or equivalent
*4: Preload the grease 45 to 55 g (1.59 to 1.94 oz) before assembling boot and shaft. After assembling boot and shaft, inject the grease
65 to 75 g (2.29 to 2.65 oz).
GI
MA
EM
LC
EC
FE
CL
MT
AT
SU
BR
ST
RS
BT
HA
SC
EL
IDX
FRONT AXLE
Service Data and Specifications (SDS)
AX-19
DYNAMIC DAMPER (WHERE FITTED)
=NLAX0033
Unit: mm (in)
QG
YD
M/T models
A/T models
LH
RH
LH
RH
LH
RH
Distance
“A”
178 - 184
(7.01 - 7.24)
375 - 381
(14.76 - 15.00)
—
398 (15.67)
172 - 178
(6.77 - 7.01)
190 -196
(7.48 - 7.72)
“B”
64 (2.52)
—
70 (2.76)
70 (2.76)
70 (2.76)
SAX015
WHEEL BEARING (FRONT)
NLAX0021
Wheel bearing axial end play limit
mm (in)
0.05 (0.0020)
Wheel bearing lock nut tightening torque
N·m (kg-m, ft-lb)
255 - 333 (26 - 34, 188 - 245)
FRONT AXLE
Service Data and Specifications (SDS) (Cont’d)
AX-20
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст