Nissan Almera Tino V10. Instruction — part 258
ABS Actuator and Electric Unit
NLBR0223S02
YBR340
REMOVAL
NLBR0223S0201
1.
Disconnect battery cable.
2.
Drain brake fluid.
3.
Remove mounting bracket fixing bolts and nuts.
4.
Disconnect connector, brake pipes and remove fixing nuts.
INSTALLATION
NLBR0223S0202
CAUTION:
After installation, refill brake fluid. Then bleed air.
1.
Connect brake pipes temporarily.
2.
Tighten fixing bolts and nuts.
3.
Tighten brake pipes.
4.
Connect connector and battery cable.
REMOVAL AND INSTALLATION
ABS
ABS Actuator and Electric Unit
BR-80
SBR984C
SBR873CA
Sensor Rotor
NLBR0223S03
REMOVAL
NLBR0223S0301
1.
Remove the drive shaft and rear wheel hub. Refer to “Drive
Shaft” and “Wheel Hub” in AX section.
2.
Remove the sensor rotor using suitable puller, drift and bear-
ing replacer.
SBR985C
INSTALLATION
NLBR0223S0302
Install the sensor rotor. For front sensor rotor, use hammer and
wooden block. For rear sensor rotor, use suitable drift and press.
I
Always replace sensor rotor with new one.
YBR343
I
Pay attention to the dimension of rear sensor rotor as show in
figure.
Height: “h”:
h: 12.5 - 13.5 mm (0.49 - 0.531 in)
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
ST
RS
BT
HA
SC
EL
IDX
REMOVAL AND INSTALLATION
ABS
Sensor Rotor
BR-81
Adjustment of Steering Angle Sensor Neutral
Position
NLBR0160
After removing/installing or replacing ABS actuator and electric unit
(control unit), steering angle sensor, steering components, suspen-
sion components, or after adjusting wheel alignment, make sure to
adjust neutral position of steering angle sensor before running
vehicle.
Situation
Adjustment of steering angle sensor neutral position
Removing/Installing ABS actuator and electric unit (control unit)
×
Removing/Installing steering angle sensor
×
Removing/Installing steering components
×
Removing/Installing suspension components
×
Change tires to new ones
–
Tire rotation
–
Adjusting wheel alignment
×
×
: Required
–: Not required
CAUTION:
To adjust neutral position of steering angle sensor, make sure
to use CONSULT-II.
(Adjustment cannot be done without CONSULT-II.)
MBIB0906E
1.
Stop vehicle with front wheels in straight-ahead position.
2.
Connect CONSULT-II and CONSUL-II CONVERTER to data
link connector on vehicle, and turn ignition switch ON (do not
start engine).
3.
Touch “ABS”, “WORK SUPPORT” and “ST ANGLE SENSOR
ADJUSTMENT” on CONSULT-II screen in this order.
SFIA0371E
4.
Touch “START”.
CAUTION:
Do not touch steering wheel while adjusting steering angle
sensor.
5.
After approximately 10 seconds, touch “END”. (After approxi-
mately 60 seconds, it ends automatically.)
6.
Turn ignition switch OFF, then turn it ON again.
CAUTION:
Be sure to perform above operation.
7.
Run vehicle with front wheels in straight-ahead position, then
stop.
ON-VEHICLE SERVICE
ESP/TCS/ABS
Adjustment of Steering Angle Sensor Neutral Position
BR-82
8.
Select “DATA MONITOR”, “SELECTION FROM MENU”, and
“STR ANGLE SIG” on CONSULT-II screen. Then make sure
“STR ANGLE SIG” is within 0
±
2.5 deg. If value is more than
specification, repeat steps 3 to 7.
9.
Erase memory of ABS actuator and electric unit (control unit)
and ECM.
10. Turn ignition switch to OFF.
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
ST
RS
BT
HA
SC
EL
IDX
ON-VEHICLE SERVICE
ESP/TCS/ABS
Adjustment of Steering Angle Sensor Neutral Position (Cont’d)
BR-83
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст