Nissan Almera Tino V10. Instruction — part 35
Nickel Metal Hydride Battery Replacement
NLGI0007S06
CONSULT-II contains a nickel metal hydride battery. When replac-
ing the battery obey the following:
WARNING:
Replace the nickel metal hydride battery with Genuine CON-
SULT-II battery only. Use of another battery may present a risk
of fire or explosion. The battery may present a fire or chemi-
cal burn hazard if mistreated. Do not recharge, disassemble or
dispose of in fire.
Keep the battery out of reach of children and discard used
battery conforming to the local regulations.
Checking Equipment
NLGI0007S07
When ordering the below equipment, contact your NISSAN
distributor.
Tool name
Description
NISSAN CONSULT-II
q
1
CONSULT-II unit (Tester internal soft:
Resident version 3.3.0) and accessories
q
2
Program card AED02E and AEN02C
(For NATS)
To confirm the best combination of these
softwares, refer to CONSULT-II Operation
Instruction.
q
3
CONSULT-II CONVERTER
SAIA0362E
NOTE:
I
The CONSULT-II must be used in conjunction with a pro-
gram card.
CONSULT-II does not require loading (Initialization) proce-
dure.
I
Be sure the CONSULT-II is turned off before installing or
removing a program card.
CAUTION:
I
If CONSULT-II is used with no connection of CONSULT-II
CONVERTER, malfunctions might be detected in self-di-
agnosis depending on control unit which carry out CAN
communication.
I
If CONVERTER is not connected with CONSULT-II, vehicle
occur the “FAIL-SAFE MODE” which is “LIGHT UP the
HEADLIGHT” and/or “Cooling FAN ROTATING” when
CONSULT-II is started.
CONSULT-II CHECKING SYSTEM
Nickel Metal Hydride Battery Replacement
GI-36
PAIA0070E
CONSULT-II Start Procedure
=NLGI0007S09
1.
Turn ignition switch OFF.
2.
Connect CONSULT-II and CONSULT-II CONVERTER to the
data link connector.
SKIA3098E
3.
Turn ignition switch ON.
4.
Touch “START (NISSAN BASED VECL)” or “System Shortcut”
(eg: Engine) on the screen.
CONSULT-II Data Link Connector (DLC) Circuit
NLGI0007S08
SGI125A
INSPECTION PROCEDURE
NLGI0007S0801
If the CONSULT-II cannot diagnose the system properly, check the
following items.
Symptom
Check item
CONSULT-II cannot access any
system.
I
CONSULT-II DLC power supply circuit (Terminal 8) and ground circuit (Terminal 4)
(For detailed circuit, refer to “MIL & Data Link Connectors Wiring Diagram” in EC section.)
I
CONSULT-II DDL cable and CONSULT-II CONVERTER
CONSULT-II cannot access indi-
vidual system. (Other systems
can be accessed.)
I
CONSULT-II program card (Check the appropriate CONSULT-II program card for the system.
Refer to “Checking Equipment”.)
I
Power supply and ground circuit for the control unit of the system
(For detailed circuit, refer to wiring diagram for each system.)
I
Open or short circuit between the system and CONSULT-II DLC
(For detailed circuit, refer to wiring diagram for each system.)
NOTE:
The DDL1 and DDL2 circuits from DLC pins 12, 13, 14 and 15
may be connected to more than one system. A short in a DDL
circuit connected to a control unit in one system may affect
CONSULT-II access to other systems.
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
CONSULT-II CHECKING SYSTEM
CONSULT-II Start Procedure
GI-37
NLGI0008
Model Variation
NLGI0008S01
Body
Engine
Transaxle
Grade
Destination
RHD
LHD
MPV
QG18DE
RF5F70A
GX
TATAREF-EE5
TATALEF-EG5
RE4F03B
TATAREA-EE5
TATALEA-EG5
YD22DDT*1
RS5F50A
TVHAREF-TE5
TVHALEF-TG5
YD22DDTi*2
RS6F51R
TVHAREY-TE5
TVHALEY-TG5
*1: Without intercooler
*2: With intercooler
PREFIX AND SUFFIX DESIGNATIONS
NLGI0008S0112
YGI011
IDENTIFICATION INFORMATION
Model Variation
GI-38
Identification Number
NLGI0008S02
NGI054
VEHICLE IDENTIFICATION NUMBER ARRANGEMENT
NLGI0008S0201
YGI012
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
IDENTIFICATION INFORMATION
Identification Number
GI-39
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст