Nissan Almera Tino V10. Instruction — part 114
AT-180
[EURO-OBD]
DTC P0755 SHIFT SOLENOID VALVE B
Wiring Diagram — AT — SSV/B
ECS0098I
YAT380A
DTC P0755 SHIFT SOLENOID VALVE B
AT-181
[EURO-OBD]
D
E
F
G
H
I
J
K
L
M
A
B
AT
Diagnostic Procedure
ECS0098J
1.
CHECK VALVE RESISTANCE
1.
Turn ignition switch to “OFF” position.
2.
Disconnect terminal cord assembly connector in engine compartment.
3.
Check resistance between terminal 1 and ground.
OK or NG
OK
>> GO TO 2
NG
>> 1. Remove control valve assembly. Refer to
"Control Valve Assembly and Accumulators"
.
2. Check the following items:
–
Shift solenoid valve B
Refer to
AT-182, "Component Inspection"
.
–
Harness of terminal cord assembly for short or open
2.
CHECK POWER SOURCE CIRCUIT
1.
Turn ignition switch to “OFF” position.
2.
Disconnect TCM harness connector.
3.
Check continuity between terminal 12 and TCM harness connector terminal 1.
If OK, check harness for short to ground and short to power.
4.
Reinstall any part removed.
OK or NG
OK
>> GO TO 3
NG
>> Repair open circuit or short to ground or short to power
in harness or connectors.
3.
CHECK DTC
Perform
AT-179, "DIAGNOSTIC TROUBLE CODE (DTC) CONFIRMATION PROCEDURE"
.
OK or NG
OK
>> INSPECTION END
NG
>> 1. Perform TCM input/output signal inspection.
2. If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
Resistance: 5 - 20
Ω
MCIA0093E
Continuity should exist.
MCIA0094E
AT-182
[EURO-OBD]
DTC P0755 SHIFT SOLENOID VALVE B
Component Inspection
ECS0098K
SHIFT SOLENOID VALVE B
●
For removal, refer to
AT-410, "Control Valve Assembly and Accumulators"
.
Resistance Check
●
Check resistance between two terminals.
Operation Check
●
Check solenoid valve by listening for its operating sound while
applying battery voltage to the terminal and ground.
Solenoid valve
Terminal No.
Resistance
(Approx.)
Shift solenoid
valve B
1
Ground
5 - 20
Ω
MCIA0072E
MCIA0095E
DTC P1705 ACCELERATOR PEDAL POSITION (APP) SENSOR
AT-183
[EURO-OBD]
D
E
F
G
H
I
J
K
L
M
A
B
AT
DTC P1705 ACCELERATOR PEDAL POSITION (APP) SENSOR
PFP:22620
Description
ECS0098L
●
Accelerator pedal position (APP) sensor (throttle position sensor),
Electric throttle control actuator consists of throttle control motor,
acceleration pedal position sensor, throttle position sensor, etc. The
actuator sends a signal to the TCM.
CONSULT-II REFERENCE VALUE IN DATA MONITOR MODE
Remarks: Specification data are reference values.
TCM TERMINALS AND REFERENCE VALUE
Remarks: Specification data are reference values.
ON BOARD DIAGNOSIS LOGIC
MCIA0096E
Monitor item
Condition
Specification
Throttle position sensor
(Accelerator pedal position (APP) sensor)
Fully-closed throttle
Approximately 0.5V
Fully-open throttle
Approximately 4V
Termi-
nal No.
Wire color
Item
Condition
Judgement standard
(Approx.)
32
R
Throttle position
sensor
(Power source)
or
When turning ignition switch to “ON”
4.5 - 5.5V
When turning ignition switch to “OFF”
0V
41
GY
Throttle position
sensor
When depressing accelerator pedal
slowly after warming up engine.
(Voltage rises gradually in response
to throttle position.)
Fully-closed throttle:
0.5V
Fully-open throttle:
4V
42
B
Ground
(Throttle position
sensor)
—
—
—
Diagnostic trouble code
Malfunction is detected when...
Check items (Possible cause)
: TP SEN/CIRC A/T
TCM receives an excessively low or high
voltage from the sensor.
●
Harness or connectors
(The sensor circuit is open or shorted.)
●
Accelerator pedal position (APP) sensor
Throttle position sensor
: P1705
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст