Nissan Almera Tino V10. Instruction — part 519
EC-902
[QG (WITHOUT EURO-OBD)]
IVT CONTROL SOLENOID VALVE
6.
CHECK CRANKSHAFT POSITION SENSOR (POS)
Refer to
EC-743, "Component Inspection"
.
OK or NG
OK
>> GO TO 7.
NG
>> Replace crankshaft position sensor (POS).
7.
CHECK CAMSHAFT POSITION SENSOR (PHASE)
Refer to
EC-750, "Component Inspection"
.
OK or NG
OK
>> GO TO 8.
NG
>> Replace camshaft position sensor (PHASE).
8.
CHECK CAMSHAFT (INTAKE)
Check the following.
●
Accumulation of debris to the signal plate of camshaft rear end
●
Chipping signal plate of camshaft rear end
OK or NG
OK
>> GO TO 9.
NG
>> Remove debris and clean the signal plate of camshaft
rear end or replace camshaft.
9.
CHECK INTERMITTENT INCIDENT
Refer to
EC-644, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
.
>> INSPECTION END
Component Inspection
EBS00R3G
INTAKE VALVE TIMING CONTROL SOLENOID VALVE
1.
Disconnect intake valve timing control solenoid valve harness connector.
2.
Check resistance between intake valve timing control solenoid
valve terminals 1 and 2.
Removal and Installation
EBS00R3H
INTAKE VALVE TIMING CONTROL SOLENOID VALVE
Refer to
.
PBIB0565E
Terminals
Resistance
1 and 2
Approximately 8
Ω
at 20
°
C (68
°
F)
1 or 2 and ground
∞Ω
(Continuity should not exist)
PBIB0574E
PNP SWITCH
EC-903
[QG (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
PNP SWITCH
PFP:32006
Component Description
EBS00R3I
When the gear position is “P” (A/T models only) or “N”, park/neutral position (PNP) switch is “ON”.
ECM detects the position because the continuity of the line (the “ON” signal) exists.
CONSULT-II Reference Value in Data Monitor Mode
EBS00R3J
Specification data are reference values.
MONITOR ITEM
CONDITION
SPECIFICATION
P/N POSI SW
●
Ignition switch: ON
Shift lever:
P or N (A/T models)
Neutral (M/T models)
ON
Shift lever: Except above
OFF
EC-904
[QG (WITHOUT EURO-OBD)]
PNP SWITCH
Wiring Diagram
EBS00R3K
YEC491A
PNP SWITCH
EC-905
[QG (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
Specification data are reference values and are measured between each terminal and ground.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
Diagnostic Procedure
EBS00R3L
1.
CHECK OVERALL FUNCTION
With CONSULT-II
1.
Turn ignition switch “ON”.
2.
Select “P/N POSI SW” in “DATA MONITOR” mode with CON-
SULT-II.
3.
Check the “P/N POSI SW” signal under the following conditions.
Without CONSULT-II
1.
Turn ignition switch “ON”.
2.
Check voltage between ECM terminal 102 and ground under the
following conditions.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 2.
TER-
MINAL
NO.
WIRE COLOR
ITEM
CONDITION
DATA (DC Voltage)
102
P (A/T models)
G/OR (M/T models)
PNP switch
[Ignition switch “ON”]
●
Shift lever position is “P” or “N” (A/T models),
“Neutral” (M/T models).
Approximately 0V
[Ignition switch “ON”]
●
Except the above gear position
A/T models
BATTERY VOLTAGE
(11 - 14V)
M/T models
Approximately 5V
Selector lever position
P/N POSI SW signal
“P” and “N” position (A/T models)
Neutral position (M/T models)
ON
Except the above position
OFF
PBIB0102E
Selector lever position
Voltage
“P” and “N” position (A/T models)
Neutral position (M/T models)
Approximately 0V
Except the above position
A/T models: Battery voltage
M/T models: Approximately 5V
MBIB0043E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст