Nissan Almera Tino V10. Instruction — part 880
EM-176
[YD]
PRIMARY TIMING CHAIN
PRIMARY TIMING CHAIN
PFP:13028
Removal and Installation
EBS00QFS
CAUTION:
●
After removing timing chain, do not turn crankshaft and camshaft separately, or valves will strike
piston heads.
●
When installing camshafts, chain tensioners, oil seals or other sliding parts, lubricate contacting
surfaces with new engine oil.
●
Apply new engine oil to parts marked in illustration before installation.
PRIMARY TIMING CHAIN
EM-177
[YD]
C
D
E
F
G
H
I
J
K
L
M
A
EM
MBIA0027E
1.
Fuel pump
2.
Chain tensioner
3.
Slack guide
4.
Camshaft sprocket
5.
Fuel pump sprocket
6.
Tension guide
EM-178
[YD]
PRIMARY TIMING CHAIN
REMOVAL
1.
Remove engine and transaxle. Refer to
EM-197, "Removal and Installation"
.
2.
Remove transaxle from engine. place engine onto engine stand (SST). Refer to
.
3.
Remove oil pan. Refer to
EM-137, "Removal and Installation"
.
4.
Remove oil filter bracket. Refer to LC-28, “Oil Filter Bracket”.
5.
Remove injection tube and fuel injector. Refer to
EM-147, "Removal and Installation"
.
6.
Remove secondary timing chain and associated parts. Refer to
EM-171, "Removal and Installation"
.
7.
When removing rear chain case, remove camshaft sprockets. Refer to
EM-162, "Removal and Installa-
.
8.
Remove crankshaft pulley.
a.
Hold crankshaft pulley with the pulley holder (SST).
b.
Loosen crankshaft pulley fixing bolt and pull out the bolt approx-
imately 10 mm (0.39 in).
c.
Using pulley puller (SST), remove crankshaft pulley.
●
Use two M6 bolts with approx. 60 mm (2.36 in) shank length
for securing crankshaft pulley.
9.
Remove oil pump housing.
●
Loosen bolts in the reverse order of that shown in the figure
and remove them.
●
Use seal cutter (SST) etc. for removal.
10. Remove front oil seal from oil pump housing.
●
Punch out the seal off from the back surface of the oil pump
using a flat-bladed screwdriver.
●
Be careful not to damage the oil pump housing.
7.
Chain guide
8.
Spacer
9.
Front chain case
10.
Crankshaft pully
11.
Front oil seal
12.
Oil pump housing
13.
Primary timing chain
14.
Oil pump drive spacer.
15.
Crankshaft sprocket
16.
Secondary timing chain
17.
Rear chain case
18.
Power steering pump
JEM131G
JEM132G
JEM133G
PRIMARY TIMING CHAIN
EM-179
[YD]
C
D
E
F
G
H
I
J
K
L
M
A
EM
11. Remove chain tensioner.
●
When removing chain tensioner, push the sleeve of chain
tensioner and keep it pressed with a push pin, etc.
12. Remove timing chain slack guide.
13. Hold fuel pump sprocket and remove bolt.
a.
Insert positioning stopper pin (SST) into the hole 6 mm (0.24 in)
in the diameter on the fuel pump sprocket.
b.
Using a TORX wrench (SST), turn pump shaft little by little to
adjust the position of fuel pump sprocket so that the holes align.
c.
Push positioning stopper pin (SST) through fuel pump sprocket
to fuel pump body to hold pump sprocket, and remove bolt.
14. Remove primary timing chain with fuel pump sprocket and
crankshaft sprocket.
15. Remove chain guide and tension guides.
16. Remove fuel pump.
17. Remove power steering pump.
JEM134G
MBIA0049E
PBIC0945E
MBIA0079E
MBIA0080E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст