Nissan Murano. Instruction — part 699
EXL-208
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
PARKING, LICENSE PLATE AND TAIL LAMPS SYSTEM
Component Parts Location
INFOID:0000000009723011
Component Description
INFOID:0000000009723012
1.
Parking lamp
2.
Front side marker lamp
3.
Combination switch
4.
Rear side marker lamp
5.
Tail lamp
6.
License plate lamp
7.
IPDM E/R
8.
BCM
9.
Tail lamp indicator lamp
A.
Engine room (LH)
B.
Behind the combination meter
C.
On the combination meter
JPLIA0892ZZ
Part
Description
BCM
• Detects each switch condition by the combination switch reading function.
• Judges the ON/OFF status of the parking, license plate and tail lamps according to
the vehicle condition.
- Requests the tail lamp relay ON to IPDM E/R (with CAN communication).
- Requests the tail lamp indicator lamp ON to the combination meter (with CAN com-
munication).
IPDM E/R
Controls the integrated relay and supplies voltage to the load according to the request
from BCM (with CAN communication).
Combination switch
(Lighting & turn signal switch)
Combination meter
(Tail lamp indicator lamp)
Turns the tail lamp indicator lamp ON according to the request from BCM (with CAN
communication).
EXTERIOR LAMP BATTERY SAVER SYSTEM
EXL-209
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
EXTERIOR LAMP BATTERY SAVER SYSTEM
System Diagram
INFOID:0000000009723013
System Description
INFOID:0000000009723014
OUTLINE
• Exterior lamp battery saver system is controlled by each function of BCM and IPDM E/R.
Control by BCM
- Combination switch reading function
- Headlamp control function
- Exterior lamp battery saver function
Control by IPDM E/R
- Relay control function
• BCM turns the exterior lamp* OFF after a period of time to prevent the battery from over-discharge when the
ignition switch is turned OFF with the exterior lamp ON.
*: Headlamp (LO/HI), parking lamp, side marker lamp, tail lamp, license plate lamp and front fog lamp.
EXTERIOR LAMP BATTERY SAVER ACTIVATION
BCM activates the timer and turns the exterior lamp OFF 5 minutes after the ignition switch is turned from ON
→
OFF with the exterior lamps ON.
NOTE:
• Headlamp control function turns the exterior lamps ON normally when the ignition switch is turned ACC or
the engine started (both before and after the exterior lamp battery saver is turned OFF).
• The timer starts at the time that the lighting switch is turned from OFF
→
1ST or 2ND with the exterior lamp
OFF.
JPLIA1037GB
EXL-210
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
EXTERIOR LAMP BATTERY SAVER SYSTEM
Component Parts Location
INFOID:0000000009723015
Component Description
INFOID:0000000009723016
1.
Combination switch
2.
IPDM E/R
3.
BCM
A.
Engine room (LH)
B.
Behind the combination meter
JPLIA0845ZZ
Part
Description
BCM
• Detects each switch condition by the combination switch reading function.
• Activates the battery saver to turn the exterior lamps OFF according to the vehicle
condition.
- Requests each relay OFF to IPDM E/R (with CAN communication).
IPDM E/R
Controls the integrated relay according to the request from BCM (with CAN communi-
cation).
Combination switch
(Lighting & turn signal switch)
DIAGNOSIS SYSTEM (BCM)
EXL-211
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000010092628
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
NOTE:
• *1: For models with rain sensor this mode is displayed, but is not used.
• *2: This item is displayed, but is not used.
FREEZE FRAME DATA (FFD)
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
*
1
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
×
—
AIR CONDITONER*
2
• Intelligent Key system
• Engine start system
INTELLIGENT KEY
×
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NVIS - NATS
IMMU
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Back door opener system
TRUNK
×
×
Vehicle security system
THEFT ALM
×
×
×
RAP system
RETAINED PWR
×
Signal buffer system
SIGNAL BUFFER
×
×
TPMS
TPMS (AIR PRESSURE MONITOR)
×
×
×
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст