Nissan Murano. Instruction — part 760
PREPARATION
FAX-35
< PREPARATION >
[AWD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
Commercial Service Tool
INFOID:0000000009717915
Tool name
Description
Power tool
Loosening bolts and nuts
PBIC0190E
FAX-36
< PERIODIC MAINTENANCE >
[AWD]
FRONT WHEEL HUB AND KNUCKLE
PERIODIC MAINTENANCE
FRONT WHEEL HUB AND KNUCKLE
Inspection
INFOID:0000000009717916
MOUNTING INSPECTION
Make sure that the mounting conditions (looseness, backlash) of each component and component conditions
(wear, damage) are normal.
WHEEL BEARING INSPECTION
• Move wheel hub and bearing assembly in the axial direction by hand. Make sure there is no looseness of
wheel bearing.
• Rotate wheel hub and bearing assembly and make sure there is no unusual noise or other irregular condi-
tions. If there is any of irregular conditions, replace wheel hub and bearing assembly.
Standard
Axial end play
: Refer to
.
FRONT DRIVE SHAFT
FAX-37
< PERIODIC MAINTENANCE >
[AWD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
FRONT DRIVE SHAFT
Inspection
INFOID:0000000009717917
• Check drive shaft mounting point and joint for looseness and other damage.
• Check boot for cracks and other damage.
CAUTION:
Replace entire drive shaft assembly when noise or vibration occurs from drive shaft.
FAX-38
< REMOVAL AND INSTALLATION >
[AWD]
FRONT WHEEL HUB AND KNUCKLE
REMOVAL AND INSTALLATION
FRONT WHEEL HUB AND KNUCKLE
Exploded View
INFOID:0000000009717918
Removal and Installation
INFOID:0000000009717919
REMOVAL
1.
Remove tires with power tool.
2.
Remove wheel sensor and sensor harness. Refer to
BRC-123, "FRONT WHEEL SENSOR : Exploded
.
3.
Remove lock plate from strut assembly. Refer to
BR-22, "FRONT : Exploded View"
.
4.
Remove caliper assembly. Hang caliper assembly not to interfere with work. Refer to
CALIPER ASSEMBLY (1 PISTON TYPE) : Exploded View"
(1 PISTON TYPE),
ASSEMBLY (2 PISTON TYPE) : Exploded View"
(2 PISTON TYPE).
CAUTION:
Never depress brake pedal while brake caliper is removed.
5.
Remove disc rotor. Refer to
BR-39, "BRAKE CALIPER ASSEMBLY (1 PISTON TYPE) : Removal and
(1 PISTON TYPE),
BR-43, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) : Removal and
(2 PISTON TYPE).
6.
Remove cotter pin, and then loosen wheel hub lock nut with power tool.
7.
Patch wheel hub lock nut with a piece of wood. Hammer the wood to disengage wheel hub and bearing
assembly from drive shaft.
CAUTION:
• Never place drive shaft joint at an extreme angle. Also be careful not to overextend slide joint.
• Never allow drive shaft to hang down without support for joint sub-assembly, shaft and the other
parts.
NOTE:
Use suitable puller, if wheel hub and bearing assembly and drive shaft cannot be separated even after
performing the above procedure.
8.
Remove wheel hub lock nut.
9.
Remove strut assembly from steering knuckle. Refer to
.
1.
Steering knuckle
2.
Splash guard
3.
Wheel hub and bearing assembly
4.
Wheel hub lock nut
5.
Cotter pin
Refer to
for symbols in the figure.
JPDIF0274GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст