Nissan Murano. Instruction — part 1294
SRC-24
< DTC/CIRCUIT DIAGNOSIS >
[FOR USA AND CANADA]
B0001 DRIVER AIR BAG MODULE
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
CHECK DTC
Perform each inspection according to the displayed DTC.
Which DTC is displayed?
[OPEN] >> GO TO 4.
[VB-SHORT] >> GO TO 8.
[GND-SHORT]>> GO TO 5.
[SHORT] >> GO TO 6.
4.
CHECK SPIRAL CABLE CIRCUIT 1
1.
Turn ignition switch OFF.
2.
Disconnect driver air bag module harness connector and combination switch (spiral cable) harness con-
nector.
3.
Check continuity between driver air bag module harness connector and combination switch (spiral cable)
harness connector.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Replace combination switch (spiral cable). Refer to
SR-15, "Removal and Installation"
.
5.
CHECK SPIRAL CABLE CIRCUIT 2
1.
Turn ignition switch OFF.
2.
Disconnect driver air bag module harness connector and combination switch (spiral cable) harness con-
nector.
3.
Check continuity between driver air bag module harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Replace combination switch (spiral cable). Refer to
SR-15, "Removal and Installation"
.
6.
CHECK SPIRAL CABLE CIRCUIT 3
1.
Turn ignition switch OFF.
2.
Disconnect driver air bag module harness connector and combination switch (spiral cable) harness con-
nector.
3.
Check continuity between combination switch (spiral cable) terminals.
Driver air bag module
Combination switch (spiral cable)
Continuity
Connector
Terminal
Connector
Terminal
M350
10
M32
28
Existed
11
30
M351
9
12
29
Driver side air bag module
Ground
Continuity
Connector
Terminal
M350
10
Not existed
11
M351
9
12
B0001 DRIVER AIR BAG MODULE
SRC-25
< DTC/CIRCUIT DIAGNOSIS >
[FOR USA AND CANADA]
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Replace combination switch (spiral cable). Refer to
SR-15, "Removal and Installation"
.
7.
CHECK SPIRAL CABLE CIRCUIT 4
Check continuity between combination switch (spiral cable) terminals.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Replace combination switch (spiral cable). Refer to
SR-15, "Removal and Installation"
.
8.
REPLACE COMBINATION SWITCH (SPIRAL CABLE)
1.
Replace combination switch (spiral cable). Refer to
SR-15, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 9.
NO
>> INSPECTION END
9.
REPLACE DRIVER AIR BAG MODULE
1.
Replace driver air bag module. Refer to
SR-12, "Removal and Installation"
.
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 10.
NO
>> INSPECTION END
10.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-26, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Combination switch (spiral cable)
Continuity
Connector
Terminal
M350
10
11
Not existed
M351
9
12
Combination switch (spiral cable)
Continuity
Connector
Terminal
M32
28
30
Not existed
29
SRC-26
< DTC/CIRCUIT DIAGNOSIS >
[FOR USA AND CANADA]
B0002 DRIVER AIR BAG MODULE
B0002 DRIVER AIR BAG MODULE
DTC Logic
INFOID:0000000009718487
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-15, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009718488
WARNING:
DTC
CONSULT screen items
(Trouble diagnosis content)
DTC detecting condition
Possible cause
B0002
DRIVER AIRBAG MOD-
ULE 2
[Driver Frontal Stage 2 De-
ployment Control (Sub-
fault)]
[OPEN]
Driver air bag module circuit is
open
(including the spiral cable)
• Connection malfunction
or open circuit of har-
ness and connector
• Internal malfunction of
driver air bag module
• Internal malfunction of
air bag diagnosis sensor
unit
[VB-SHORT]
Driver air bag module circuit is
shorted to power supply circuit
(including the spiral cable)
• Connection malfunction
or short circuit to power
supply of harness and
connector
• Internal malfunction of
driver air bag module
• Internal malfunction of
air bag diagnosis sensor
unit
[GND-SHORT]
Driver air bag module circuit is
shorted to ground
(including the spiral cable)
• Connection malfunction
or short circuit to ground
of harness and connec-
tor
• Internal malfunction of
driver air bag module
• Internal malfunction of
air bag diagnosis sensor
unit
[SHORT]
Driver air bag module circuits are
shorted to each other
(including the spiral cable)
• Connection malfunction
or short circuit of har-
ness and connector
• Internal malfunction of
driver air bag module
• Internal malfunction of
air bag diagnosis sensor
unit
B0002 DRIVER AIR BAG MODULE
SRC-27
< DTC/CIRCUIT DIAGNOSIS >
[FOR USA AND CANADA]
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
CHECK DTC
Perform each inspection according to the displayed DTC.
Which DTC is displayed?
[OPEN] >> GO TO 4.
[VB-SHORT] >> GO TO 8.
[GND-SHORT]>> GO TO 5.
[SHORT] >> GO TO 6.
4.
CHECK SPIRAL CABLE CIRCUIT 1
1.
Turn ignition switch OFF.
2.
Disconnect driver air bag module harness connector and combination switch (spiral cable) harness con-
nector.
3.
Check continuity between driver air bag module harness connector and combination switch (spiral cable)
harness connector.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Replace combination switch (spiral cable). Refer to
SR-15, "Removal and Installation"
.
5.
CHECK SPIRAL CABLE CIRCUIT 2
1.
Turn ignition switch OFF.
2.
Disconnect driver air bag module harness connector and combination switch (spiral cable) harness con-
nector.
3.
Check continuity between driver air bag module harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 9.
Driver air bag module
Combination switch (spiral cable)
Continuity
Connector
Terminal
Connector
Terminal
M350
10
M32
28
Existed
11
30
M351
9
12
29
Driver side air bag module
Ground
Continuity
Connector
Terminal
M350
10
Not existed
11
M351
9
12
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст