Nissan Murano. Instruction — part 977
LAN
ECM BRANCH LINE CIRCUIT
LAN-219
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 10)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ECM BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000010093479
1.
CHECK CONNECTOR
1.
Turn the ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check the following terminals and connectors for damage, bend and loose connection (unit side and con-
nector side).
-
Models with automatic back door system
•
ECM
•
Harness connector E104
•
Harness connector B4
-
Models without automatic back door system
•
ECM
•
Harness connector E105
•
Harness connector M11
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Disconnect the connector of ECM.
2.
Check the resistance between the ECM harness connector terminals.
Is the measurement value within the specification?
YES
>> GO TO 3.
NO
>> Repair the ECM branch line.
3.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the ECM. Refer to
Is the inspection result normal?
YES (Present error)>>Replace the ECM. Refer to
EC-16, "ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Special Repair Requirement"
YES (Past error)>>Error was detected in the ECM branch line.
NO
>> Repair the power supply and the ground circuit.
ECM harness connector
Resistance (
Ω
)
Connector No.
Terminal No.
E16
98
97
Approx. 108 – 132
LAN-220
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 10)]
PWBD BRANCH LINE CIRCUIT
PWBD BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000010093480
1.
CHECK CONNECTOR
1.
Turn the ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check the terminals and connectors of the automatic back door control unit for damage, bend and loose
connection (unit side and connector side).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Disconnect the connector of automatic back door control unit.
2.
Check the resistance between the automatic back door control unit harness connector terminals.
Is the measurement value within the specification?
YES
>> GO TO 3.
NO
>> Repair the automatic back door control unit branch line.
3.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the automatic back door control unit. Refer to
"AUTOMATIC BACK DOOR CONTROL UNIT : Diagnosis Procedure"
Is the inspection result normal?
YES (Present error)>>Replace the automatic back door control unit. Refer to
.
YES (Past error)>>Error was detected in the automatic back door control unit branch line.
NO
>> Repair the power supply and the ground circuit.
Automatic back door control unit harness connector
Resistance (
Ω
)
Connector No.
Terminal No.
B8
6
7
Approx. 54 – 66
LAN
4WD BRANCH LINE CIRCUIT
LAN-221
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 10)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
4WD BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000010093481
1.
CHECK CONNECTOR
1.
Turn the ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check the terminals and connectors of the AWD control unit for damage, bend and loose connection (unit
side and connector side).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Disconnect the connector of AWD control unit.
2.
Check the resistance between the AWD control unit harness connector terminals.
Is the measurement value within the specification?
YES
>> GO TO 3.
NO
>> Repair the AWD control unit branch line.
3.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the AWD control unit. Refer to
.
Is the inspection result normal?
YES (Present error)>>Replace the AWD control unit. Refer to
DLN-53, "Removal and Installation"
YES (Past error)>>Error was detected in the AWD control unit branch line.
NO
>> Repair the power supply and the ground circuit.
AWD control unit harness connector
Resistance (
Ω
)
Connector No.
Terminal No.
M69
8
16
Approx. 54 – 66
LAN-222
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 10)]
AV BRANCH LINE CIRCUIT
AV BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000010093482
1.
CHECK CONNECTOR
1.
Turn the ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check the terminals and connectors of the AV control unit for damage, bend and loose connection (unit
side and connector side).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Disconnect the connector of AV control unit.
2.
Check the resistance between the AV control unit harness connector terminals.
-
Models with navigation system
-
Models without navigation system
Is the measurement value within the specification?
YES
>> GO TO 3.
NO
>> Repair the AV control unit branch line.
3.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the AV control unit. Refer to the following.
• Base audio with color display:
AV-118, "AV CONTROL UNIT : Diagnosis Procedure"
• BOSE audio without navigation:
AV-244, "AV CONTROL UNIT : Diagnosis Procedure"
• BOSE audio with navigation:
AV-419, "AV CONTROL UNIT : Diagnosis Procedure"
Is the inspection result normal?
YES (Present error)>>Replace the AV control unit. Refer to the following.
• Base audio with color display:
AV-149, "Removal and Installation"
• BOSE audio without navigation:
AV-276, "Removal and Installation"
AV-448, "Removal and Installation"
YES (Past error)>>Error was detected in the AV control unit branch line.
NO
>> Repair the power supply and the ground circuit.
AV control unit harness connector
Resistance (
Ω
)
Connector No.
Terminal No.
M180
90
74
Approx. 54 – 66
AV control unit harness connector
Resistance (
Ω
)
Connector No.
Terminal No.
M174
81
80
Approx. 54 – 66
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст