Nissan Murano. Instruction — part 908
PRECAUTIONS
INT-9
< PRECAUTION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
FOR USA AND CANADA : Precautions for Removing of Battery Terminal
INFOID:0000000009956129
• When removing the 12V battery terminal, turn OFF the ignition
switch and wait at least 30 seconds.
NOTE:
ECU may be active for several tens of seconds after the ignition
switch is turned OFF. If the battery terminal is removed before ECU
stops, then a DTC detection error or ECU data corruption may
occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be
detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
FOR USA AND CANADA : Precaution for Work
INFOID:0000000009720357
• After removing and installing the opening/closing parts, be sure to carry out fitting adjustments to check their
operation.
• Check the lubrication level, damage, and wear of each part. If necessary, grease or replace it.
FOR MEXICO
FOR MEXICO : Precaution for Supplemental Restraint System (SRS) "AIR BAG" and
"SEAT BELT PRE-TENSIONER"
INFOID:0000000009720358
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Instruction.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
SEF289H
INT-10
< PRECAUTION >
PRECAUTIONS
FOR MEXICO : Precaution for Procedure without Cowl Top Cover
INFOID:0000000009720359
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.
FOR MEXICO : Precautions for Removing of Battery Terminal
INFOID:0000000009956130
• When removing the 12V battery terminal, turn OFF the ignition
switch and wait at least 30 seconds.
NOTE:
ECU may be active for several tens of seconds after the ignition
switch is turned OFF. If the battery terminal is removed before ECU
stops, then a DTC detection error or ECU data corruption may
occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be
detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
FOR MEXICO : Precaution for Work
INFOID:0000000009720360
• After removing and installing the opening/closing parts, be sure to carry out fitting adjustments to check their
operation.
• Check the lubrication level, damage, and wear of each part. If necessary, grease or replace it.
PIIB3706J
SEF289H
PREPARATION
INT-11
< PREPARATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
PREPARATION
PREPARATION
Commercial Service Tools
INFOID:0000000009720361
Special Service Tools
INFOID:0000000009720362
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool name
Description
Engine ear
Locates the noise
Remover tool
Removes the clips, pawls and metal clips
Power tool
Loosening bolts, nuts and screws
SIIA0995E
JMKIA3050ZZ
PIIB1407E
Tool number
(Kent-Moore No.)
Tool name
Description
(J-39570)
Chassis ear
Locates the noise
(J-50397)
NISSAN Squeak and Rattle
Kit
Repairs the cause of noise
SIIA0993E
SIIA0994E
INT-12
< PREPARATION >
CLIP LIST
CLIP LIST
Clip List
INFOID:0000000009720363
JMJIA3734GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст