Nissan Murano. Instruction — part 272
PRECAUTIONS
CO-9
< PRECAUTION >
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
If for some unavoidable reason tool such as a screwdriver is used, be careful not to damage the mat-
ing surfaces.
LIQUID GASKET APPLICATION PROCEDURE
1.
Using a scraper (A), remove old liquid gasket adhering to the liq-
uid gasket application surface and the mating surface.
• Remove liquid gasket completely from the groove of the liquid
gasket application surface, mounting bolts, and bolt holes.
2.
Wipe the liquid gasket application surface and the mating sur-
face with white gasoline (lighting and heating use) to remove
adhering moisture, grease and foreign materials.
3.
Attach liquid gasket tube to the tube presser (commercial ser-
vice tool).
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-22, "Recommended Chemical Products and Sealants"
.
4.
Apply liquid gasket without breaks to the specified location with
the specified dimensions.
• If there is a groove for the liquid gasket application, apply liq-
uid gasket to the groove.
• As for the bolt holes (B), normally apply liquid gasket inside
the holes. Occasionally, it should be applied outside the holes.
Check to read the text of service instruction.
• Within five minutes of liquid gasket application, install the mat-
ing component.
• If liquid gasket protrudes, wipe it off immediately.
• Never retighten after mounting bolts and nuts the installation.
• After 30 minutes or more have passed from the installation, fill
engine oil and engine coolant.
CAUTION:
If there are specific instructions in this instruction, observe them.
JPBIA0053ZZ
EMA0622D
A
: Groove
: Inside
JPBIA0010ZZ
CO-10
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000009720474
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
INFOID:0000000009720475
Tool number
(Kent-Moore No.)
Tool name
Description
KV10111100
(J-37228)
Seal cutter
Removing water pump cover
NT046
Tool name
Description
Tube presser
Pressing the tube of liquid gasket
Power tool
Loosening nuts and bolts
Radiator cap tester
Checking radiator and radiator cap
Radiator cap tester adapter
Adapting radiator cap tester to radiator cap
and radiator pipe (upper) filler neck
a: 28 (1.10) dia.
b: 31.4 (1.236) dia.
c: 41.3 (1.626) dia.
Unit: mm (in)
S-NT052
PBIC0190E
PBIC1982E
S-NT564
ENGINE COOLANT
CO-11
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
PERIODIC MAINTENANCE
ENGINE COOLANT
Inspection
INFOID:0000000009720476
LEVEL
• Check if the reservoir tank engine coolant level is within the “MIN”
to “MAX” when the engine is cool.
• Adjust the engine coolant level if necessary.
CAUTION:
Refill Genuine NISSAN Long Life Antifreeze/Coolant (blue) or
equivalent in its quality mixed with water (distilled or demineral-
ized). Refer to
MA-15, "FOR NORTH AMERICA : Fluids and
(FOR MEXICO).
LEAKAGE
• To check for leakage, apply pressure to the cooling system with the
radiator cap tester (commercial service tool) (A) and radiator cap
tester adapter (commercial service tool) (B).
WARNING:
Never remove radiator cap when engine is hot. Serious burns
could occur from high-pressure engine coolant escaping from
radiator.
CAUTION:
Higher test pressure than specified may cause radiator dam-
age.
NOTE:
In a case that engine coolant decreases, replenish radiator with engine coolant.
• If anything is found, repair or replace damaged parts.
Draining
INFOID:0000000009720477
WARNING:
• To avoid being scalded, never change engine coolant when the engine is hot.
• Wrap a thick cloth around radiator cap and carefully remove radiator cap. First, turn radiator cap a
quarter of a turn to release built-up pressure. Then turn radiator cap all the way.
1.
Remove engine under cover.
2.
Open radiator drain plug (1) at the bottom of radiator, and then
remove radiator cap.
When draining all of engine coolant in the system, open water drain plugs on cylinder block. Refer
to
.
A
: MAX
B
: MIN
JPBIA0102ZZ
Testing pressure
: Refer to
.
PBIC5121J
: Vehicle front
JPBIA1684ZZ
CO-12
< PERIODIC MAINTENANCE >
ENGINE COOLANT
3.
Remove reservoir tank if necessary, and drain engine coolant and clean reservoir tank before installing.
4.
Check drained engine coolant for contaminants such as rust, corrosion or discoloration.
If contaminated, flush the engine cooling system. Refer to
.
Refilling
INFOID:0000000009720478
CAUTION:
• Do not reuse O-rings.
• Do not put additive such as waterleak preventive, since it may cause cooling waterway clogging.
• When refilling use Genuine NISSAN Long Life Antifreeze/Coolant (blue) or equivalent in its quality
mixed with water (distilled or demineralized). Refer to
MA-15, "FOR NORTH AMERICA : Fluids and
(for North America) or Refer to
MA-16, "FOR MEXICO : Fluids and Lubricants"
(for Mex-
ico).
1.
Install reservoir tank if removed and radiator drain plug.
CAUTION:
Be sure to clean drain plug and install with new O-ring.
If water drain plugs on cylinder block are removed, close and tighten them. Refer to
2.
Check that each hose clamp has been firmly tightened.
3.
Remove air duct assembly and air cleaner cases (upper and lower) assembly. Refer to
.
4.
Disconnect heater hose (1) at the position (
) in the figure.
5.
Fill radiator, and reservoir tank if removed, to specified level.
CAUTION:
Never adhere the engine coolant to electronic equipments.
(alternator etc.)
• Pour engine coolant through engine coolant filler neck
slowly of less than 2 (2-1/8 US qt, 1-3/4 lmp qt) a minute
to allow air in system to escape.
• When engine coolant overflows disconnected heater
hose, connect heater hose, and continue filling the engine
coolant.
Tightening torque
: Refer to
: Vehicle front
JPBIA1685ZZ
JPBIA0412ZZ
Engine coolant capacity
: Refer to
CO-31, "Periodical Maintenance Spec-
(With reservoir tank at “MAX” level)
Reservoir tank engine coolant capacity
: Refer to
CO-31, "Periodical Maintenance
(At “MAX” level)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст