Nissan Murano. Instruction — part 16
ADP-56
< DTC/CIRCUIT DIAGNOSIS >
POWER SUPPLY AND GROUND CIRCUIT
2.
CHECK GROUND CIRCUIT
Check continuity between the automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES
>> Automatic drive positioner control unit power supply and ground circuit are OK.
NO
>> Repair or replace harness.
AUTOMATIC DRIVE POSITIONER CONTROL UNIT : Special Repair Requirement
INFOID:0000000009720680
1.
PERFORM ADDITIONAL SERVICE
Perform additional service when removing battery negative terminal.
>> Refer to
ADP-8, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL
.
Automatic drive positioner control unit
Ground
Continuity
Connector
Terminal
M104
30
Existed
SLIDING SWITCH
ADP-57
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
SLIDING SWITCH
Description
INFOID:0000000009720681
Sliding switch is equipped to the power seat switch on the seat cushion side surface. The operation signal is
inputted to the driver seat control unit when the sliding switch is operated.
Component Function Check
INFOID:0000000009720682
1.
CHECK FUNCTION
1.
Select “SLIDE SW-FR”, “SLIDE SW-RR” in “Data monitor” mode with CONSULT.
2.
Check sliding switch signal under the following conditions.
Is the indication normal?
YES
>> INSPECTION END
NO
>> Perform diagnosis procedure. Refer to
Diagnosis Procedure
INFOID:0000000009720683
1.
CHECK SLIDING SWITCH SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect power seat switch connector.
3.
Turn ignition switch ON.
4.
Check voltage between power seat switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK SLIDING SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect driver seat control unit connector.
3.
Check continuity between driver seat control unit harness connector and power seat switch harness con-
nector.
4.
Check continuity between driver seat control unit harness connector and ground.
Monitor item
Condition
Status
SLIDE SW-FR
Sliding switch (forward)
Operate
ON
Release
OFF
SLIDE SW-RR
Sliding switch (backward)
Operate
ON
Release
OFF
(+)
(–)
Voltage (V)
(Approx.)
Power seat switch
Connector
Terminals
B459
11
Ground
Battery voltage
12
Driver seat control unit
Power seat switch
Continuity
Connector
Terminal
Connector
Terminal
B452
11
B459
11
Existed
12
12
ADP-58
< DTC/CIRCUIT DIAGNOSIS >
SLIDING SWITCH
Is the inspection result normal?
YES
>> Replace driver seat control unit. Refer to
ADP-210, "Removal and Installation"
NO
>> Repair or replace harness or connector.
3.
CHECK SLIDING SWITCH
ADP-58, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace power seat switch. Refer to
ADP-213, "Removal and Installation"
4.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000009720684
1.
CHECK SLIDING SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect power seat switch (sliding switch) connector.
3.
Check continuity between power seat switch (sliding switch) terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace power seat switch. Refer to
ADP-213, "Removal and Installation"
.
Driver seat control unit
Ground
Continuity
Connector
Terminal
B452
11
Not existed
12
Power seat switch (Sliding switch)
Condition
Continuity
Terminal
35
11
Sliding switch (backward)
Operate
Existed
Release
Not existed
12
Sliding switch (forward)
Operate
Existed
Release
Not existed
RECLINING SWITCH
ADP-59
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
RECLINING SWITCH
Description
INFOID:0000000009720685
Reclining switch is equipped to the power seat switch on the seat cushion side surface. The operation signal is
inputted to the driver seat control unit when the reclining switch is operated.
Component Function Check
INFOID:0000000009720686
1.
CHECK FUNCTION
1.
Select “RECLN SW-FR”, “RECLN SW-RR” in “Data monitor” mode with CONSULT.
2.
Check reclining switch signal under the following conditions.
Is the indication normal?
YES
>> INSPECTION END
NO
>> Perform diagnosis procedure. Refer to
Diagnosis Procedure
INFOID:0000000009720687
1.
CHECK RECLINING SWITCH SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect power seat switch connector.
3.
Turn ignition switch ON.
4.
Check voltage between power seat switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK RECLINING SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect driver seat control unit connector.
3.
Check continuity between driver seat control unit harness connector and power seat switch harness con-
nector.
4.
Check continuity between driver seat control unit harness connector and ground.
Monitor item
Condition
Status
RECLINE SW-FR
Reclining switch (forward)
Operate
ON
Release
OFF
RECLINE SW-RR
Reclining switch (backward)
Operate
ON
Release
OFF
(+)
(–)
Voltage (V)
(Approx.)
Power seat switch
Connector
Terminals
B459
13
Ground
Battery voltage
14
Driver seat control unit
Power seat switch
Continuity
Connector
Terminal
Connector
Terminal
B452
13
B459
13
Existed
14
14
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст