Nissan Murano. Instruction — part 1297
SRC-36
< DTC/CIRCUIT DIAGNOSIS >
[FOR USA AND CANADA]
B0021 CURTAIN AIR BAG MODULE
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE CURTAIN AIR BAG MODULE LH
1.
Replace curtain air bag module LH. Refer to
SR-20, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-26, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
B0028 SIDE AIR BAG MODULE
SRC-37
< DTC/CIRCUIT DIAGNOSIS >
[FOR USA AND CANADA]
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B0028 SIDE AIR BAG MODULE
DTC Logic
INFOID:0000000009718497
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-15, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009718498
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
DTC
CONSULT screen items
(Trouble diagnosis content)
DTC detecting condition
Possible cause
B0028
SIDE A/B MODULE RH
[Right Side Airbag Deploy-
ment Control 1 (Subfault)]
[OPEN]
Side air bag module RH
circuit is open
• Connection malfunction or open
circuit of harness and connector
• Internal malfunction of side air
bag module RH
• Internal malfunction of air bag di-
agnosis sensor unit
[VB-SHORT]
Side air bag module RH
circuit is shorted to power
supply circuit
• Connection malfunction or short
circuit to power supply of har-
ness and connector
• Internal malfunction of side air
bag module RH
• Internal malfunction of air bag di-
agnosis sensor unit
[GND-SHORT]
Side air bag module RH
circuit is shorted to ground
• Connection malfunction or short
circuit to ground of harness and
connector
• Internal malfunction of side air
bag module RH
• Internal malfunction of air bag di-
agnosis sensor unit
[SHORT]
Side air bag module RH
circuits are shorted to
each other
• Connection malfunction or short
circuit of harness and connector
• Internal malfunction of side air
bag module RH
• Internal malfunction of air bag di-
agnosis sensor unit
SRC-38
< DTC/CIRCUIT DIAGNOSIS >
[FOR USA AND CANADA]
B0028 SIDE AIR BAG MODULE
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE SIDE AIR BAG MODULE RH
1.
Replace side air bag module RH. Refer to
SE-98, "Removal and Installation"
.
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-26, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
B0029 CURTAIN AIR BAG MODULE
SRC-39
< DTC/CIRCUIT DIAGNOSIS >
[FOR USA AND CANADA]
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B0029 CURTAIN AIR BAG MODULE
DTC Logic
INFOID:0000000009718499
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-15, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009718500
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
DTC
CONSULT screen items
(Trouble diagnosis content)
DTC detecting condition
Possible cause
B0029
CURTAIN A/B MODULE
RH
[Right Curtain Deployment
Control 1 (Subfault)]
[OPEN]
Curtain air bag module RH
circuit is open
• Connection malfunction or open
circuit of harness and connector
• Internal malfunction of curtain
air bag module RH
• Internal malfunction of air bag
diagnosis sensor unit
[VB-SHORT]
Curtain air bag module RH
circuit is shorted to power
supply circuit
• Connection malfunction or short
circuit to power supply of har-
ness and connector
• Internal malfunction of curtain
air bag module RH
• Internal malfunction of air bag
diagnosis sensor unit
[GND-SHORT]
Curtain air bag module RH
circuit is shorted to ground
• Connection malfunction or short
circuit to ground of harness and
connector
• Internal malfunction of curtain
air bag module RH
• Internal malfunction of air bag
diagnosis sensor unit
[SHORT]
Curtain air bag module RH
circuits are shorted to each
other
• Connection malfunction or short
circuit of harness and connector
• Internal malfunction of curtain
air bag module RH
• Internal malfunction of air bag
diagnosis sensor unit
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст