Nissan Murano. Instruction — part 773
FSU-14
< REMOVAL AND INSTALLATION >
FRONT STABILIZER
FRONT STABILIZER
Exploded View
INFOID:0000000009721411
Removal and Installation
INFOID:0000000009721412
REMOVAL
1.
Remove tires power tool.
2.
Remove front exhaust tube. Refer to
3.
Remove rear propeller shaft from transfer. (AWD models) Refer to
.
4.
Remove lock plate. Refer to
BR-22, "FRONT : Exploded View"
.
5.
Remove wheel sensor harness from strut assembly. Refer to
BRC-123, "FRONT WHEEL SENSOR :
.
6.
Disconnect power steering solenoid valve harness connector. Refer to
ST-48, "Removal and Installation"
7.
Remove steering outer socket from steering knuckle. Refer to
.
8.
Remove stabilizer connecting rod.
9.
Remove mounting bolts (
) of stabilizer clamp, and then
remove stabilizer clamp and stabilizer bushing from front sus-
pension member.
10. Remove stabilizer bar.
INSTALLATION
Note the following, and install in the reverse order of removal.
1.
Stabilizer clamp
2.
Stabilizer bushing
3.
Stabilizer bar
4.
Front suspension member
5.
Stabilizer connecting rod
Refer to
for symbols in the figure.
JPEIA0092GB
WEIA0182E
FRONT STABILIZER
FSU-15
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
• Install stabilizer clamp that notch (A) becomes vehicle front side
(
).
• Install stabilizer bushing that slit (B) becomes vehicle front side
(
).
Inspection
INFOID:0000000009721413
INSPECTION AFTER REMOVAL
Check stabilizer bar, stabilizer connecting rod, stabilizer bushing and stabilizer clamp for deformation, cracks
or damage. Replace it if necessary.
JPEIA0058ZZ
FSU-16
< UNIT REMOVAL AND INSTALLATION >
FRONT SUSPENSION MEMBER
UNIT REMOVAL AND INSTALLATION
FRONT SUSPENSION MEMBER
Exploded View
INFOID:0000000009721414
Removal and Installation
INFOID:0000000009721415
REMOVAL
1.
Remove tires with power tool.
2.
Remove air guide mounting nuts (
) and air guide (1).
3.
At first, remove the engine and the transaxle assembly with front
suspension member downward. Then separate the engine, tran-
saxle and drive shaft. Refer to
(AWD).
4.
Remove the following parts.
• Steering knuckle and wheel hub and bearing assembly: Refer
to
(AWD).
• Steering gear assembly and hydraulic line: Refer to
• Stabilizer bar: Refer to
• Transverse link: Refer to
.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of installation position between front suspension member and transverse links (rub-
ber bushing) under unladen condition with tires on level ground.
Inspection
INFOID:0000000009721416
INSPECTION AFTER REMOVAL
Check the front suspension member for significant deformation, cracks, or damages. Replace it if necessary.
INSPECTION AFTER INSTALLATION
1.
Front suspension member
2.
Rebound stopper
3.
Front suspension member stay
Refer to
for symbols in the figure.
JPEIA0093GB
JPEIA0097ZZ
FRONT SUSPENSION MEMBER
FSU-17
< UNIT REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
1.
Check wheel sensor harness for proper connection. Refer to
BRC-123, "FRONT WHEEL SENSOR :
.
2.
Check wheel alignment. Refer to
3.
Adjust neutral position of steering angle sensor. Refer to
BRC-9, "ADJUSTMENT OF STEERING ANGLE
SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст