Nissan Murano. Instruction — part 1187
WHEEL ALIGNMENT
RSU-7
< PERIODIC MAINTENANCE >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
• If camber is exceeds the standard value, adjust with adjusting bolt
(1) in front lower link (2).
CAUTION:
After adjusting camber, be sure to check toe-in.
- If camber is not still within the specification, inspect and replace
any damaged or worn suspension parts.
TOE-IN
• If toe-in is exceeds the standard value, adjust with adjusting bolt
(1) in rear lower link (2).
CAUTION:
• Be sure to adjust equally on right and left side with adjust-
ing bolt.
• When tightening the nut firmly and checking the torque, use
a wrench to prevent the turning of the bolt.
- If toe-in is not still within the specification, inspect and replace any
damaged or worn suspension parts.
- After toe-in adjustment, adjust neutral position of steering angle
sensor. Refer to
BRC-9, "ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Special
Camber: Refer to
.
JPEIB0080ZZ
Toe-In: Refer to
JPEIB0081ZZ
RSU-8
< REMOVAL AND INSTALLATION >
REAR LOWER LINK & COIL SPRING
REMOVAL AND INSTALLATION
REAR LOWER LINK & COIL SPRING
Exploded View
INFOID:0000000009721426
Removal and Installation
INFOID:0000000009721427
REMOVAL
1.
Remove tires with power tool.
2.
Remove stabilizer connecting rod (lower side). Refer to
3.
Set jack under rear lower link.
4.
Loosen rear lower link mounting bolt and nut (rear suspension member side), and then remove rear lower
link mounting bolt and nut (axle housing side) with power tool.
5.
Slowly lower jack, then remove upper seat, coil spring and rubber seat from rear lower link.
6.
Remove rear lower link mounting bolt and nut (rear suspension member side), and remove rear lower link.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Make sure that upper seat is attached as shown in the figure.
CAUTION:
• Make sure keep the upper seat (1) to place protrusion for
projection (A) on outside of vehicle (lateral direction of vehi-
cle).
• Make sure that the projection (C) on upper seat inside is
securely fitted on the bracket (2) tabs (B).
• Match up rubber seat indentions and rear lower link grooves and
attach.
1.
Upper seat
2.
Coil spring
3.
Rubber seat
4.
Rear lower link
5.
Rear suspension member
6.
Radius rod
7.
Front lower link
Refer to
for symbols in the figure.
JPEIB0146GB
: Body
JPEIB0082ZZ
REAR LOWER LINK & COIL SPRING
RSU-9
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
• Install coil spring by aligning lower end of the coil spring to step (A)
between rubber seat (1) and rear lower link (2).
CAUTION:
Set coil spring so that its paint marks are aligned with the
positions of 3.5 turns (2 places) and 4.5 turns (1 place) from
the bottom end of the coil spring.
• Perform the final tightening of rear suspension member and axle
installation position (rubber bushing) under unladen condition with
tires on level ground.
Inspection
INFOID:0000000009721428
INSPECTION AFTER REMOVAL
Check rear lower link, bushing and coil spring for deformation, crack, and damage. Replace it if necessary.
INSPECTION AFTER INSTALLATION
1.
Check wheel alignment. Refer to
2.
Adjust neutral position of steering angle sensor. Refer to
BRC-9, "ADJUSTMENT OF STEERING ANGLE
SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
JPEIB0013ZZ
RSU-10
< REMOVAL AND INSTALLATION >
REAR SHOCK ABSORBER
REAR SHOCK ABSORBER
Exploded View
INFOID:0000000009721429
Removal and Installation
INFOID:0000000009721430
REMOVAL
1.
Remove tires with power tool.
2.
Separate stabilizer connecting rod (lower side). Refer to
3.
Set suitable jack under axle housing to relieve the coil spring tension.
4.
Remove shock absorber mounting bolt (lower side) with power tool.
5.
Gradually lower the jack to remove it from front lower link.
6.
Remove shock absorber assembly mounting nuts (upper side)
(
), and remove shock absorber assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of bolts and nuts at the shock absorber lower side (rubber bushing), under unladen
conditions with tires on level ground.
Disassembly and Assembly
INFOID:0000000009721431
DISASSEMBLY
CAUTION:
Never damage shock absorber piston rod when removing components from shock absorber.
1.
Shock absorber
2.
Piston rod lock nut
3.
Shock absorber mounting bracket
4.
Bound bumper
Refer to
for symbols in the figure.
JPEIB0135GB
JPEIB0060ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст