Nissan Murano. Instruction — part 374
DOOR LOCK ACTUATOR
DLK-107
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1.
Use CONSULT to perform Active Test (“DOOR LOCK”).
2.
Touch “ALL LCK” or “ALL UNLK” to check that it works normally.
Is the inspection result normal?
YES
>> Door lock actuator is OK.
NO
>> Refer to
DLK-107, "REAR RH : Diagnosis Procedure"
REAR RH : Diagnosis Procedure
INFOID:0000000009719003
1.
CHECK DOOR LOCK ACTUATOR SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect rear door lock assembly RH.
3.
Check voltage between rear door lock assembly RH harness connector and ground.
Is the inspection result normal?
YES
>> Replace rear door lock assembly RH. Refer to
DLK-323, "DOOR ASSEMBLY : Removal and
NO
>> GO TO 2.
2.
CHECK DOOR LOCK ACTUATOR CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and rear door lock assembly RH harness connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-98, "Removal and Installation"
NO
>> Repair or replace harness.
(+)
(–)
Condition of door lock and
unlock switch
Voltage (V)
(Approx.)
Rear door lock assembly RH
Connector
Terminal
D105
5
Ground
Lock
0
→
Battery voltage
→
0
6
Unlock
0
→
Battery voltage
→
0
BCM
Rear door lock assembly RH
Continuity
Connector
Terminal
Connector
Terminal
M119
8
D105
5
Existed
10
6
BCM
Ground
Continuity
Connector
Terminal
M119
8
Not Existed
10
DLK-108
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
BACK DOOR OPENER ACTUATOR
BACK DOOR OPENER ACTUATOR
Description
INFOID:0000000009719004
Back door opener actuator open back door from BCM.
Component Function Check
INFOID:0000000009719005
1.
CHECK FUNCTION
1.
Perform Active Test (“TRUNK/GLASS HATCH”) with CONSULT.
2.
Touch “OPEN” and check that back door opens.
Is the inspection result normal?
YES
>> Back door opener actuator is OK.
NO
>> Refer to
DLK-108, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000009719006
1.
CHECK OUTPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect back door lock assembly.
3.
Check voltage between back door lock assembly harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK BACK DOOR OPENER ACTUATOR CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and back door lock assembly (back door opener actu-
ator) harness connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-98, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK BACK DOOR OPENER ACTUATOR GROUND CIRCUIT
Check continuity between back door lock assembly harness connector and ground.
(+)
(–)
Condition of back door
opener switch
Voltage (V)
(Approx.)
Back door lock assembly
Connector
Terminal
D180
1
Ground
ON
0
→
Battery voltage
→
0
BCM
Back door lock assembly
Continuity
Connector
Terminal
Connector
Terminal
M120
23
D180
1
Existed
BCM
Ground
Continuity
Connector
Terminal
M120
23
Not existed
Back door lock assembly
Ground
Continuity
Connector
Terminal
D180
2
Existed
BACK DOOR OPENER ACTUATOR
DLK-109
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection normal?
YES
>> Replace back door lock assembly. Refer to
DLK-351, "DOOR LOCK : Removal and Installation"
NO
>> Repair or replace harness.
DLK-110
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
KEY CYLINDER SWITCH
KEY CYLINDER SWITCH
Description
INFOID:0000000009719007
Power window main switch detects condition of the door key cylinder switch and transmits to BCM as the
LOCK or UNLOCK signals.
Component Function Check
INFOID:0000000009719008
1.
CHECK DOOR KEY CYLINDER SWITCH INPUT SIGNAL
Check (“KEY CYL LK-SW”, “KEY CYL UN-SW”) in “DATA MONITOR” mode for “POWER DOOR LOCK SYS-
TEM” with CONSULT. Refer to
DLK-55, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
.
Is the inspection result normal?
YES
>> Key cylinder switch is OK.
NO
>> Refer to
DLK-110, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000009719009
1.
CHECK DOOR KEY CYLINDER SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front door lock assembly (driver side).
3.
Check voltage between front door lock assembly (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK DOOR KEY CYLINDER SIGNAL CIRCUIT
1.
Disconnect power window main switch connector.
2.
Check continuity between power window main switch harness connector and front door lock assembly
(driver side) harness connector.
3.
Check continuity between power window main switch connector and ground.
Monitor item
Condition
KEY CYL LK-SW
Lock
: ON
Neutral / Unlock
: OFF
KEY CYL UN-SW
Unlock
: ON
Neutral / Lock
: OFF
(+)
(–)
Voltage (V)
(Approx.)
Front door lock assembly (driver side)
Connector
Terminal
D9
5
Ground
5
6
Power window main switch
Front door lock assembly (driver side)
Continuity
Connector
Terminal
Connector
Terminal
D5
4
D9
6
Existed
6
5
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст