Nissan Murano. Instruction — part 26
ADP-96
< DTC/CIRCUIT DIAGNOSIS >
TELESCOPIC SENSOR
4.
Check continuity between driver seat control unit harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness or connector.
3.
CHECK TELESCOPIC SENSOR POWER SUPPLY
1.
Connect driver seat control unit connector.
2.
Turn ignition switch ON.
3.
Check voltage between telescopic motor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 4.
4.
CHECK TELESCOPIC SENSOR POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit connector.
3.
Check continuity between automatic drive positioner control unit harness connector and telescopic motor
harness connector.
4.
Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit. Refer to
ADP-211, "Removal and Installation"
.
NO
>> Repair or replace harness or connecter.
5.
CHECK TELESCOPIC SENSOR GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit connector.
3.
Check continuity between automatic drive positioner control unit harness connector and telescopic motor
harness connector.
Driver seat control unit
Telescopic motor
Continuity
Connector
Terminal
Connector
Terminal
B452
31
M117
5
Existed
Driver seat control unit
Ground
Continuity
Connector
Terminal
B452
31
Not existed
(+)
(–)
Voltage (V)
(Approx.)
Telescopic motor
Connector
Terminals
M117
4
Ground
Battery voltage
Automatic drive positioner control unit
Telescopic motor
Continuity
Connector
Terminal
Connector
Terminal
M104
27
M117
4
Existed
Automatic drive positioner control unit
Ground
Continuity
Connector
Terminal
M104
27
Not existed
Automatic drive positioner control unit
Telescopic motor
Continuity
Connector
Terminal
Connector
Terminal
M75
20
M117
6
Existed
TELESCOPIC SENSOR
ADP-97
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
Is the inspection result normal?
YES
>> Replace telescopic motor.
NO
>> Repair or replace harness or connecter.
ADP-98
< DTC/CIRCUIT DIAGNOSIS >
MIRROR SENSOR
MIRROR SENSOR
DRIVER SIDE
DRIVER SIDE : Description
INFOID:0000000009720741
• The mirror sensor (driver side) is installed to the door mirror (driver side).
• The resistance of 2 sensors (horizontal and vertical) is changed when the door mirror (driver side) is oper-
ated.
• Automatic drive positioner control unit calculates the door mirror position according to the change of the volt-
age of 2 sensor input terminals.
DRIVER SIDE : Component Function Check
INFOID:0000000009720742
1.
CHECK FUNCTION
1.
Select “MIR/SEN LH U-D”, “MIR/SEN LH R-L” in “Data monitor” with CONSULT.
2.
Check mirror sensor (driver side) signal under the following condition.
Is the indication normal?
YES
>> INSPECTION END
NO
>> Perform diagnosis procedure. Refer to
ADP-98, "DRIVER SIDE : Diagnosis Procedure"
.
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000009720743
1.
CHECK DOOR MIRROR (DRIVER SIDE) SENSOR POWER SUPPLY
1.
Turn ignition switch OFF.
2.
Disconnect door mirror (driver side) connector.
3.
Turn ignition switch ON.
4.
Check voltage between door mirror (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK DOOR MIRROR (DRIVER SIDE) SENSOR POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit connector.
3.
Check continuity between automatic drive positioner control unit harness connector and door mirror
(driver side) harness connector.
4.
Check continuity between automatic drive positioner control unit harness connector and ground.
Monitor item
Condition
Value
MIR/SEN LH U-D
Door mirror (driver side)
Change between
3.4 [V] (close to peak)
0.6 [V] (close to valley)
MIR/SEN LH R-L
Change between
0.6 [V] (close to left edge)
3.4 [V] (close to right edge)
(+)
(–)
Voltage (V)
(Approx.)
Door mirror (driver side)
Connector
Terminals
D3
23
Ground
5
Automatic drive positioner control unit
Door mirror (driver side)
Continuity
Connector
Terminal
Connector
Terminal
M75
21
D3
23
Existed
MIRROR SENSOR
ADP-99
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit. Refer to
ADP-211, "Removal and Installation"
.
NO
>> Repair or replace harness or connector.
3.
CHECK DOOR MIRROR (DRIVER SIDE) SENSOR GROUND
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit connector.
3.
Check continuity between automatic drive positioner control unit harness connector and door mirror
(driver side) harness connector.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness or connector.
4.
CHECK DOOR MIRROR (DRIVER SIDE) SENSOR CIRCUIT
1.
Check continuity between automatic drive positioner control unit harness connector and door mirror
(driver side) harness connector.
2.
Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace door mirror sensor. (Built in driver side mirror.)
NO
>> Repair or replace harness or connector.
PASSENGER SIDE
PASSENGER SIDE : Description
INFOID:0000000009720744
• The mirror sensor (passenger side) is installed to the door mirror (passenger side).
• The resistance of 2 sensors (horizontal and vertical) is changed when the door mirror (passenger side) is
operated.
• Automatic drive positioner control unit calculates the door mirror position according to the change of the volt-
age of 2 sensor input terminals.
PASSENGER SIDE : Component Function Check
INFOID:0000000009720745
1.
CHECK FUNCTION
1.
Select “MIR/SEN RH U-D”, “MIR/SEN RH R-L” in “Data monitor” with CONSULT.
2.
Check the mirror sensor (passenger side) signal under the following conditions.
Automatic drive positioner control unit
Ground
Continuity
Connector
Terminal
M75
21
Not existed
Automatic drive positioner control unit
Door mirror (driver side)
Continuity
Connector
Terminal
Connector
Terminal
M75
20
D3
24
Existed
Automatic drive positioner control unit
Door mirror (driver side)
Continuity
Connector
Terminal
Connector
Terminal
M75
6
D3
21
Existed
18
22
Automatic drive positioner control unit
Ground
Continuity
Connector
Terminal
M75
6
Not existed
18
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст