Nissan Murano. Instruction — part 688
EXL-164
< SYMPTOM DIAGNOSIS >
[XENON TYPE]
EXTERIOR LIGHTING SYSTEM SYMPTOMS
Turn signal indicator lamp
does not blink.
(Turn signal indicator
lamp is normal.)
One side
Combination meter
—
Both sides
(Always)
• Turn indicator signal
- Combination meter
- BCM
• Combination meter
• Combination meter
Data monitor "TURN IND"
• BCM (FLASHER)
Active test "FLASHER"
Both sides
(Only when activating
hazard warning lamp
with the ignition switch
OFF)
• Combination meter power sup-
ply and the ground circuit
• Combination meter
Combination meter
Power supply and the ground circuit
Refer to
.
• Hazard warning lamp does not activate.
• Hazard warning lamp continues activating.
(Turn signal is normal.)
• Hazard switch
• Harness between the hazard
switch and BCM
• BCM
Hazard switch
Refer to
.
Symptom
Possible cause
Inspection item
NORMAL OPERATING CONDITION
EXL-165
< SYMPTOM DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
NORMAL OPERATING CONDITION
Description
INFOID:0000000009722945
XENON HEADLAMP
• Brightness and the color of light may change slightly immediately after turning the headlamp ON until the
xenon bulb becomes stable. This is normal.
• Illumination time lag may occur between right and left. This is normal.
AUTO LIGHT SYSTEM
The headlamp may not be turned ON/OFF immediately after passing dark area or bright area (short tunnel,
sky bridge, shadowed area etc.) while using the auto light system. This causes the control difference. This is
normal.
EXL-166
< SYMPTOM DIAGNOSIS >
[XENON TYPE]
BOTH SIDE HEADLAMPS DO NOT SWITCH TO HIGH BEAM
BOTH SIDE HEADLAMPS DO NOT SWITCH TO HIGH BEAM
Description
INFOID:0000000009722946
The headlamp (both sides) does not switch to the high beam when setting to the lighting switch HI or PASS.
Diagnosis Procedure
INFOID:0000000009722947
1.
COMBINATION SWITCH INSPECTION
Check the combination switch. Refer to
Is the combination switch normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning part.
2.
CHECK HEADLAMP (HI) REQUEST SIGNAL INPUT
CONSULT DATA MONITOR
1.
Select “HL HI REQ” of IPDM E/R data monitor item.
2.
With operating the lighting switch, check the monitor status.
Is the item status normal?
YES
>> GO TO 3.
NO
>> Replace BCM. Refer to
3.
HEADLAMP (HI) CIRCUIT INSPECTION
Check the headlamp (HI) circuit. Refer to
EXL-36, "Component Function Check"
Is the headlamp (HI) circuit normal?
YES
>> Replace IPDM E/R.
NO
>> Repair or replace the malfunctioning part.
Monitor item
Condition
Monitor status
HL HI REQ
Lighting switch
(2ND)
HI or PASS
ON
Except for HI or
PASS
OFF
BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON
EXL-167
< SYMPTOM DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON
Description
INFOID:0000000009722948
Both side headlamps (LO) are not turned ON in any condition.
Diagnosis Procedure
INFOID:0000000009722949
1.
COMBINATION SWITCH INSPECTION
Check the combination switch. Refer to
Is the combination switch normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning part.
2.
CHECK HEADLAMP (LO) REQUEST SIGNAL INPUT
CONSULT DATA MONITOR
1.
Select “HL LO REQ” of IPDM E/R data monitor item.
2.
With operating the lighting switch, check the monitor status.
Is the item status normal?
YES
>> GO TO 3.
NO
>> Replace BCM. Refer to
.
3.
HEADLAMP (LO) CIRCUIT INSPECTION
Check the headlamp (LO) circuit. Refer to
EXL-39, "Component Function Check"
.
Is the headlamp (LO) circuit normal?
YES
>> Replace IPDM E/R.
NO
>> Repair or replace the malfunctioning part.
Monitor item
Condition
Monitor status
HL LO REQ
Lighting switch
2ND
ON
OFF
OFF
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст