Nissan Murano. Instruction — part 695
EXL-192
< REMOVAL AND INSTALLATION >
[XENON TYPE]
LICENSE PLATE LAMP
LICENSE PLATE LAMP
Exploded View
INFOID:0000000009722984
Removal and Installation
INFOID:0000000009722985
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
1.
Remove the back door finisher inner. Refer to
2.
Remove the screw. And then disconnect the license plate lamp connector.
3.
Remove the license plate lamp.
4.
Remove the screw. And then remove the license plate lamp bracket.
INSTALLATION
Install in the reverse order of removal.
Replacement
INFOID:0000000009722986
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
LICENSE PLATE LAMP BULB
1.
Remove the back door finisher inner. Refer to
2.
Turn the license plate lamp bulb socket (1) counterclockwise
and unlock it.
3.
Remove the bulb (2) from the license plate lamp bulb socket.
1.
License plate lamp bracket
2.
License plate lamp
JPLIA0826ZZ
JPLIA0827ZZ
SERVICE DATA AND SPECIFICATIONS (SDS)
EXL-193
< SERVICE DATA AND SPECIFICATIONS (SDS)
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Bulb Specifications
INFOID:0000000009722987
Item
Type
Wattage (W)
Front combination lamp
Headlamp (HI/LO)
D2S (Xenon)
35
Front turn signal lamp
WY21W (Amber)
21
Parking lamp
W5W
5
Front side marker lamp
WY5W (Amber)
5
Front fog lamp
H8
35
Rear combination lamp
Stop lamp
LED
—
Tail lamp
LED
—
Rear turn signal lamp
WY21W (Amber)
21
Rear side marker lamp
W5W
5
Back-up lamp
W16W
16
License plate lamp
W5W
5
High-mounted stop lamp
LED
—
EXL-194
< BASIC INSPECTION >
[HALOGEN TYPE]
DIAGNOSIS AND REPAIR WORK FLOW
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORK FLOW
Work Flow
INFOID:0000000009722988
OVERALL SEQUENCE
DETAILED FLOW
JMKIA8652GB
DIAGNOSIS AND REPAIR WORK FLOW
EXL-195
< BASIC INSPECTION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
1.
GET INFORMATION FOR SYMPTOM
1.
Get detailed information from the customer about the symptom (the condition and the environment when
the incident/malfunction occurs).
2.
Check operation condition of the function that is malfunctioning.
>> GO TO 2.
2.
CHECK DTC
1.
Check DTC.
2.
Perform the following procedure if DTC is detected.
-
Record DTC and freeze frame data (Print them out using CONSULT.)
-
Erase DTC.
-
Study the relationship between the cause detected by DTC and the symptom described by the customer.
3.
Check related service bulletins for information.
Are any symptoms described and any DTC detected?
Symptom is described, DTC is detected>>GO TO 3.
Symptom is described, DTC is not detected>>GO TO 4.
Symptom is not described, DTC is detected>>GO TO 5.
3.
CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer.
Also study the normal operation and fail-safe related to the symptom.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 5.
4.
CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 6.
5.
PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC CONFIRMATION PROCEDURE for the detected DTC, and then check that DTC is detected
again. At this time, always connect CONSULT to the vehicle, and check self diagnostic results in real time.
If two or more DTCs are detected, refer to DTC INSPECTION PRIORITY CHART, and determine trouble diag-
nosis order.
NOTE:
• Freeze frame data is useful if the DTC is not detected.
• Perform Component Function Check if DTC CONFIRMATION PROCEDURE is not included on Service
Instruction. This simplified check procedure is an effective alternative though DTC cannot be detected during
this check.
If the result of Component Function Check is NG, it is the same as the detection of DTC by DTC CONFIR-
MATION PROCEDURE.
Is DTC detected?
YES
>> GO TO 7.
NO
>> Check according to
GI-44, "Intermittent Incident"
.
6.
DETECT MALFUNCTIONING SYSTEM BY SYMPTOM DIAGNOSIS
Detect malfunctioning system according to SYMPTOM DIAGNOSIS based on the confirmed symptom in step
4, and determine the trouble diagnosis order based on possible causes and symptom.
Is the symptom described?
YES
>> GO TO 7.
NO
>> Monitor input data from related sensors or check voltage of related module terminals using CON-
SULT.
7.
DETECT MALFUNCTIONING PART BY DIAGNOSIS PROCEDURE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст