Nissan Murano. Instruction — part 1219
FRONT SEAT
SE-99
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
If pawl was damaged, the cover is broken by case.
a.
Remove rear outer slide cover.
i.
Pull rear outer slide cover in direction indicated by the arrow as
shown in the figure. Disengage pawls on the rear side.
ii.
Slide rear outer slide cover to the rear side to remove.
b.
Remove rear inner slide cover.
i.
Pull rear inner slide cover in direction indicated by the arrow as
shown in the figure. Disengage pawls on the rear side.
ii.
Slide rear inner slide cover to the rear side to remove.
5.
Remove the mounting bolts on the rear side of the front seat.
6.
Set seatback in a standing position.
7.
Disconnect harness connector under the seat and remove harness securing clips.
CAUTION:
Before removal, turn ignition switch OFF, disconnect battery negative terminal and then wait for at
least 3 minutes.
8.
Remove seat from the vehicle.
CAUTION:
• When removing and installing, use shop cloths to protect parts from damage.
• When removing and installing, 2 workers are required so as to prevent it from dropping.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Before installation, turn ignition switch OFF, disconnect battery negative terminal and then wait for
at least 3 minutes.
• Clamp the harness in position.
• Install the pawl more carefully.
If pawl was damaged, the cover is broken by case.
NOTE:
After installing the front seat, perform additional service when removing battery negative terminal.(With auto-
matic drive positioner model) Refer to
ADP-8, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGA-
.
Disassembly and Assembly
INFOID:0000000009718771
SEATBACK
Disassembly
1.
Remove the seatback board.
a.
Remove the seatback board band from seat cushion bottom side.
: Pawl
JMJIA6398ZZ
: Pawl
JMJIA6397ZZ
SE-100
< REMOVAL AND INSTALLATION >
FRONT SEAT
b.
Remove the seatback board mounting screws (A).
c.
Pull down the seatback board to release the pawls.
2.
Remove the seatback trim retainer (1).
3.
Disconnect the harness connectors and remove the harness clamps (power seat only).
Disconnect the seatback heater seat harness connector (A)
(heater seat only), lumbar support harness connector (B) (driver
seat only) and reclining motor harness connector (C).
4.
Remove the side air bag module.
a.
Remove the seatback trim retainer.
b.
Remove the side air bag module harness connector and harness clips from the seatback frame and seat
cushion frame.
JMJIA1420ZZ
: Pawl
JMJIA1421ZZ
JMJIA1422ZZ
JMJIA1423ZZ
FRONT SEAT
SE-101
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
c.
Remove the side air bag module cover mounting screws (A).
d.
Remove the mounting nuts, and then remove side air bag module from seatback frame.
5.
Remove the lumbar support lever knob. (Instruction lumbar support seat only.)
Pull snap ring (1) upward, and remove lumbar support lever
knob (2) from seatback frame with hook and pick tool.
6.
Remove the seatback trim and seatback pad.
a.
Use pincers, etc., to press up pawls as shown by the arrows in
the figure, and remove headrest holder from seatback.
CAUTION:
Before installing headrest holder check its orientation.
(front/rear and right/left)
b.
Remove the seatback trim and seatback pad from the seatback frame.
c.
Remove the hog rings, and separate the seatback trim and seatback pad.
7.
Remove the seatback silencer.
8.
Remove the seatback frame.
Remove the seatback frame mounting bolts (A).
Assembly
Note the following item, and assemble in the reverse order of disassembly.
CAUTION:
JMJIA1424ZZ
JMJIA0252ZZ
PIIB4084J
JMJIA1425ZZ
SE-102
< REMOVAL AND INSTALLATION >
FRONT SEAT
Install the hog rings of seatback trim in position, and then securely connect the trim or trim cord with
the pad side wire.
SEAT CUSHION
Disassembly
CAUTION:
Never disassemble front passenger seat cushion assembly.
Always replace as an assembly.
For front passenger seat service parts, refer to the service part catalogue.
1.
Remove the seatback board.
a.
Remove the seatback board fixing band on the bottom of seat cushion.
b.
Remove the seatback board mounting screws (A).
c.
Pull down the seatback board to release the pawls.
2.
Remove the seatback trim retainer (1).
3.
Disconnect the harness connectors and remove the harness clamps.
JMJIA1420ZZ
: Pawl
JMJIA1421ZZ
JMJIA1422ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст