Nissan Murano. Instruction — part 1053
MWI-92
< ECU DIAGNOSIS INFORMATION >
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
NOTE:
This operation status can be confirmed on the IPDM E/R “Data Monitor” that displays “BLOCK” for the item
“WIP PROT” while the wiper is stopped.
STARTER MOTOR PROTECTION FUNCTION
IPDM E/R turns OFF the starter control relay to protect the starter motor when the starter control relay remains
active for 90 seconds.
DTC Index
INFOID:0000000010088711
NOTE:
• The details of time display are as follows.
- CRNT: A malfunction is detected now.
- PAST: A malfunction was detected in the past.
• IGN counter is displayed on FFD (Freeze Frame data).
- The number is 0 when is detected now.
- The number increases like 1
→
2 ··· 38
→
39 after returning to the normal condition whenever IGN OFF
→
ON.
- The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
×
: Applicable
CONSULT display
Fail-safe
Refer to
No DTC is detected.
further testing
may be required.
—
—
U1000: CAN COMM CIRCUIT
×
B2098: IGN RELAY ON CIRC
×
B2099: IGN RELAY OFF CIRC
—
B210B: STR CONT RLY ON CIRC
—
B210C: STR CONT RLY OFF CIRC
—
B210D: STARTER RLY ON CIRC
—
B210E: STARTER RLY OFF CIRC
—
B210F: INTRLCK/PNP SW ON
—
B2110: INTRLCK/PNP SW OFF
—
MWI
THE FUEL GAUGE POINTER DOES NOT MOVE
MWI-93
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
SYMPTOM DIAGNOSIS
THE FUEL GAUGE POINTER DOES NOT MOVE
Description
INFOID:0000000009721310
Fuel gauge needle will not move from a certain position.
Diagnosis Procedure
INFOID:0000000009721311
1.
CONDUCTING THE COMBINATION METER SELF-DIAGNOSIS MODE
Perform the self-diagnosis mode of combination meter, and then check that the fuel gauge operates normally.
Refer to
MWI-34, "Diagnosis Description"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace the combination meter.
2.
CHECK FLOAT INTERFERENCE
Check that the float arm interferes with or binds to other components in the fuel tank.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning part.
3.
CHECK FUEL LEVEL SENSOR SIGNAL CIRCUIT
Check the fuel level sensor signal circuit. Refer to
MWI-46, "Component Function Check"
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning parts.
MWI-94
< SYMPTOM DIAGNOSIS >
THE METER CONTROL SWITCH IS INOPERATIVE
THE METER CONTROL SWITCH IS INOPERATIVE
Description
INFOID:0000000009721312
If any of the following malfunctions is found for the meter control switch operation.
• All switches are inoperative.
• The specified switch cannot be operated.
Diagnosis Procedure
INFOID:0000000009721313
1.
CHECK METER CONTROL SWITCH SIGNAL CIRCUIT
Check the meter control switch signal circuit. Refer to
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair harness or connector.
2.
CHECK METER CONTROL SWITCH
Perform a unit check for the meter control switch. Refer to
MWI-50, "Component Inspection"
Is the inspection result normal?
YES
>> Replace combination meter.
NG
>> Replace meter control switch.
MWI
THE OIL PRESSURE WARNING LAMP DOES NOT TURN ON
MWI-95
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
THE OIL PRESSURE WARNING LAMP DOES NOT TURN ON
Description
INFOID:0000000009721314
The oil pressure warning lamp stays off when the ignition switch is turned ON.
Diagnosis Procedure
INFOID:0000000009721315
1.
CHECK OIL PRESSURE WARNING LAMP
Perform auto active test. Refer to
PCS-10, "Diagnosis Description"
Is oil pressure warning lamp blinking?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
CHECK OIL PRESSURE SWITCH SIGNAL CIRCUIT
Check the oil pressure switch signal circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair harness or connector.
3.
CHECK OIL PRESSURE SWITCH
Perform a unit check for the oil pressure switch. Refer to
MWI-52, "Component Inspection"
.
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
>> Replace oil pressure switch.
4.
CHECK COMBINATION METER INPUT SIGNAL
Connect CONSULT and perform an input signal check for the combination meter. Refer to
Is the inspection result normal?
YES
>> Replace combination meter.
NO
>> Replace IPDM E/R. Refer to
PCS-37, "Removal and Installation"
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст