Nissan Murano. Instruction — part 282
DAS-18
< SYSTEM DESCRIPTION >
[LDW]
OPERATION
OPERATION
Switch Name and Function
INFOID:0000000009723213
System Display and Warning
INFOID:0000000009723214
INDICATOR LAMP AND WARNING LAMP
DISPLAY AND WARNING
JSOIA0639ZZ
No.
Switch name
Description
Warning systems switch
Turns LDW system ON/OFF
(When the setting of LDW system on the navigation system screen is ON)
LDW system setting screen
(Navigation system setting screen)
Turns setting of LDW system can be switched between ON and OFF
JSOIA0640ZZ
No.
Display item
Description
Warning systems ON indicator
Indicates that the LDW and/or BSW system is ON
Lane departure warning lamp
(Yellow)
• Blinks when LDW system is warning to driver
• Turns ON when LDW system has a malfunction
LDW ON indicator lamp
(Green)
• Turns ON when LDW system is activated
• Blinks when the back door is open
• Blinks when the washer fluid level is low
DAS
OPERATION
DAS-19
< SYSTEM DESCRIPTION >
[LDW]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
NOTE:
After the operating conditions of warning are satisfied, the warning continues until the vehicle speed reaches
approximately 60 km/h (40 MPH). Refer to
Vehicle condition/ Driver's operation
Action
Warning sys-
tems ON indi-
cator
Indication on the combination
meter
Buzzer
Less than Ap-
prox. 60 km/h
(40 MPH)
Close to lane marker
No action
ON
—
Approx. 70
km/h (45
MPH) or more
Close to lane marker
Warning
• Buzzer sounds
• Warning lamp
blinks
ON
Short con-
tinuous
beeps
• Close to lane marker
• Turn signal ON (Deviate
side)
No action
ON
—
JPOIA0021GB
JPOIA0022GB
JPOIA0021GB
DAS-20
< SYSTEM DESCRIPTION >
[LDW]
HANDLING PRECAUTION
HANDLING PRECAUTION
Precautions for Lane Departure Warning
INFOID:0000000009723215
REAR VIEW CAMERA HANDLING
The rear view camera for the LDW/BSW systems is located above the rear licence plate. To keep the proper
operation of the LDW/BSW systems and prevent a system malfunction, be sure to observe the following:
• Always keep the rear view camera clean. Be careful not to damage the nozzle of automatic washer and
blower.
• Do not attach “licence plate accessory” that reflect light.
• Do not strike or damage the areas around the rear view camera.
LANE DEPARTURE WARNING (LDW)
• The LDW system is only a warning device to inform the driver of a potential unintended lane departure. It will
not steer the vehicle or prevent loss of control. It is the driver
′
s responsibility to stay alert, drive safely, keep
the vehicle in the traveling lane, and be in control of the vehicle at all times.
• The rear view camera may not detect properly under the following conditions:
- When towing a trailer.
- When strong light enters the rear view camera. (For example, direct sunlight or headlight from the rear)
- When ambient brightness changes instantly. (For example, when the vehicle enters or exits a tunnel or
passes under a bridge.)
• Automatic washer and blower may not be able to secure detection capability when excessive dirt adheres on
the camera lens.
• LDW system may not function properly under the following conditions:
• Excessive noise (e.g. audio system volume, open vehicle window) will interfere with the chime sound, and it
may not be heard.
• The rear view camera may not be able to detect properly under the following conditions:
- On roads where there are multiple parallel lane markers; lane markers that are faded or not painted clearly;
yellow painted lane markers; non-standard lane markers; or lane markers covered with water, dirt, snow, etc.
- On roads where the discontinued lane markers are still detectable.
- On roads where there are sharply contrasting objects, such as shadows, snow, water, wheel ruts, seams or
lines remaining after road repairs. (The LDW system could detect these items as lane markers.)
- On roads where the traveling lane merges or separates.
- When the vehicle
′
s traveling direction does not align with the lane marker.
- When the road surface is very dark due to scarce ambient light or impaired tail lamp.
• When driving on curved road, warning will be late on the outside of the curve due to the nature of the sys-
tem.
DAS
DIAGNOSIS SYSTEM (CAMERA CONTROL UNIT)
DAS-21
< SYSTEM DESCRIPTION >
[LDW]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
DIAGNOSIS SYSTEM (CAMERA CONTROL UNIT)
CONSULT Function
INFOID:0000000009723216
CONSULT FUNCTIONS
CONSULT performs the following functions via the CAN communication with the camera control unit.
ECU IDENTIFICATION
Camera control unit part number can be identified.
SELF DIAGNOSIS RESULT
.
• In CONSULT self-diagnosis, self-diagnosis results and error history are displayed collectively.
• The current malfunction indicates “CRNT”. The past malfunction indicates “PAST”.
• The timing is displayed as “0” if any of the error codes [U1000] and [U1010] is detected. The counter
increases by 1 if the condition is normal at the next ignition switch ON cycle.
Freeze Frame Data (FFD)
The following vehicle status is recorded when DTC is detected and is displayed on CONSULT.
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
• Displays the status of the following vehicle signals inputted into the camera control unit.
• For each signal, actual signal can be compared with the condition recognized on the system.
Diagnosis mode
Description
ECU Identification
Camera control unit part number can be identified.
Self Diagnostic Results
Camera control unit diagnosis is performed. Current and previous malfunctions are displayed
collectively.
Data Monitor
Diagnosis of vehicle signal that is received by camera control unit can be performed.
Work Support
• Target line calibration of rear wide view can be performed.
• Display of predicted course line can be switched to ON/OFF.
• Calibration and initialization of rear view camera can be performed.
• Neutral position adjustment of steering angle sensor can be performed.
• Calibration for LDW and BSW can be performed.
• Displays causes of system cancellation occurred during system control.
Active Test
Enables an operational check of a load by transmitting a driving signal from the camera control
unit to the load.
Configuration
• The vehicle specification that is written in camera control unit can be displayed or stored.
• The vehicle specification can be written when camera control unit is replaced.
Item name
Display content
IGN counter
(0 to 39)
Numerical value is displayed indicating the number of times that ignition switch is turned ON after the DTC
is detected.
• When “0” is displayed, it indicates that the system is presently malfunctioning.
• When any numerical number other than “0” is displayed, it indicates that system malfunction in the past is
detected, but the system is presently normal.
NOTE:
Each time when ignition switch turns OFF
→
ON, numerical number increases from 1
→
2
→
3...38
→
39.
When number of times exceeds 39, numeric display does not increase and 39 is displayed until self-diag-
nosis is erased.
Display Item
Remarks
ST ANGLE SENSOR SIGNAL
[ON/OFF]
Receiving status of steering angle signal received from steering angle sensor is switched to
ON/OFF.
REVERSE SIGNAL
[ON/OFF]
Receiving status of reverse signal received from AV control unit is displayed by ON/OFF.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст