Nissan Murano. Instruction — part 31
ADP-116
< DTC/CIRCUIT DIAGNOSIS >
SEAT MEMORY INDICATOR
SEAT MEMORY INDICATOR
Description
INFOID:0000000009720769
• Memory switch is equipped on the seat memory switch installed to the driver side door trim. The operation
signal is inputted to the driver seat control unit when the memory switch is operated.
• The status of automatic drive positioner system can be checked according to the illuminating/flashing status.
Component Function Check
INFOID:0000000009720770
1.
CHECK FUNCTION
1.
Select “MEMORY SW INDCTR” in “Active test” mode with CONSULT.
2.
Check the memory indicator operation.
Is the operation of relevant parts normal?
YES
>> INSPECTION END
NO
>> Perform diagnosis procedure. Refer to
ADP-116, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000009720771
1.
CHECK SEAT MEMORY INDICATOR OPERATION
Check seat memory indicator operation.
Which is the malfunctioning indicator?
All indicators are NG>>GO TO 2.
An indicator is NG>>GO TO 4.
2.
CHECK FUSE
1.
Turn ignition switch OFF.
2.
Check that the blown fuse after repairing the affected circuit if a fuse is blown.
Is the fuse blown?
YES
>> Replace the blown fuse after repairing the affected circuit if a fuse is blown.
NO
>> GO TO 3.
3.
CHECK MEMORY INDICATOR POWER SUPPLY
Check voltage between seat memory switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace seat memory switch.Refer to
ADP-212, "Removal and Installation"
NO
>> Repair or replace harness or connector.
4.
CHECK MEMORY INDICATOR CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect driver seat control unit and seat memory switch connector.
Test item
Description
MEMORY SW INDCTR
OFF
Memory switch indicator
OFF
ON-1
Indicator 1: ON
ON-2
Indicator 2: ON
Signal name
Fuse No.
Battery power supply
10 (10A)
(+)
(–)
Voltage (V)
(Approx.)
Seat memory switch
Connector
Terminals
D13
5
Ground
Battery voltage
SEAT MEMORY INDICATOR
ADP-117
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
3.
Check continuity between driver seat control unit harness connector and seat memory switch harness
connector.
4.
Check continuity between driver seat control unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace driver seat control unit.Refer to
ADP-210, "Removal and Installation"
.
NO
>> Repair or replace harness or connector.
Driver seat control unit
Seat memory switch
Continuity
Connector
Terminal
Connector
Terminal
B452
25
D13
6
Existed
26
7
Driver seat control unit
Ground
Continuity
Connector
Terminal
B452
25
Not existed
26
ADP-118
< ECU DIAGNOSIS INFORMATION >
DRIVER SEAT CONTROL UNIT
ECU DIAGNOSIS INFORMATION
DRIVER SEAT CONTROL UNIT
Reference Value
INFOID:0000000009720772
VALUES ON THE DIAGNOSIS TOOL
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
CONSULT MONITOR ITEM
Monitor Item
Condition
Value/Status
SET SW
Set switch
Push
ON
Release
OFF
MEMORY SW1
Memory switch 1
Push
ON
Release
OFF
MEMORY SW2
Memory switch 2
Push
ON
Release
OFF
SLIDE SW–FR
Sliding switch (forward)
Operate
ON
Release
OFF
SLIDE SW–RR
Sliding switch (backward)
Operate
ON
Release
OFF
RECLN SW–FR
Reclining switch (forward)
Operate
ON
Release
OFF
RECLN SW–RR
Reclining switch (back-
ward)
Operate
ON
Release
OFF
LIFT FR SW–UP
Lifting switch front (up)
Operate
ON
Release
OFF
LIFT FR SW–DN
Lifting switch front (down)
Operate
ON
Release
OFF
LIFT RR SW–UP
Lifting switch rear (up)
Operate
ON
Release
OFF
LIFT RR SW–DN
Lifting switch rear (down)
Operate
ON
Release
OFF
MIR CON SW–UP
Mirror switch
Up
ON
Other than above
OFF
MIR CON SW–DN
Mirror switch
Down
ON
Other than above
OFF
MIR CON SW–RH
Mirror switch
Right
ON
Other than above
OFF
MIR CON SW–LH
Mirror switch
Left
ON
Other than above
OFF
MIR CHNG SW–R
Changeover switch
Right
ON
Other than above
OFF
MIR CHNG SW–L
Changeover switch
Left
ON
Other than above
OFF
DRIVER SEAT CONTROL UNIT
ADP-119
< ECU DIAGNOSIS INFORMATION >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
TILT SW-UP
Tilt switch
Upward
ON
Other than above
OFF
TILT SW-DOWN
Tilt switch
Downward
ON
Other than above
OFF
TELESCO SW-FR
Telescopic switch
Forward
ON
Other than above
OFF
TELESCO SW-RR
Telescopic switch
Backward
ON
Other than above
OFF
DETENT SW
Selector lever
P position
OFF
Other than above
ON
STARTER SW
Ignition position
Cranking
ON
Other than above
OFF
SLIDE PULSE
Seat sliding
Forward
The numeral value decreases *
Backward
The numeral value increases*
Other than above
No change to numeral value*
RECLN PULSE
Seat reclining
Forward
The numeral value decreases*
Backward
The numeral value increases
*
Other than above
No change to numeral value
*
LIFT FR PULSE
Seat lifter (front)
Up
The numeral value decreases
*
Down
The numeral value increases
*
Other than above
No change to numeral value
*
LIFT RR PULSE
Seat lifter (rear)
Up
The numeral value decreases
*
Down
The numeral value increases
*
Other than above
No change to numeral value
*
MIR/SEN RH U–D
Door mirror (passenger side)
Change between 3.4 (close to peak)
0.6 (close to valley)
MIR/SEN RH R–L
Door mirror (passenger side)
Change between 3.4 (close to left edge)
0.6 (close to right edge)
MIR/SEN LH U–D
Door mirror (driver side)
Change between 3.4 (close to peak)
0.6 (close to valley)
MIR/SEN LH R–L
Door mirror (driver side)
Change between 0.6 (close to left edge)
3.4 (close to right edge)
TILT PULSE
Tilt position
Upward
The numeral value decreases
*
Downward
The numeral value increases
*
Other than above
No change to numeral value
*
TELESCO PULSE
Telescopic position
Forward
The numeral value decreases
*
Backward
The numeral value increases
*
Other than above
No change to numeral value
*
STEERING STATUS
NOTE:
This item is displayed, but cannot be monitored
VEHICLE SPEED
The condition of vehicle speed is displayed
km/h
P RANG SW CAN
Selector lever
P position
ON
Other than above
OFF
Monitor Item
Condition
Value/Status
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст