Nissan Murano. Instruction — part 1238
B2195 ANTI-SCANNING
SEC-49
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B2195 ANTI-SCANNING
Description
INFOID:0000000009722747
When ignition switch is turned ON, BCM performs ID verification with ECM. If ID verification that is out of the
specified specification is detected, BCM prohibits further ID verification and engine cranking.
DTC Logic
INFOID:0000000009722748
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON under the following conditions.
-
Selector lever is in the P or N position
-
Do not depress brake pedal
2.
Check “Self-diagnostic result” using CONSULT.
Is DTC detected?
YES
>> Refer to
NO
>> INSPECTION END.
Diagnosis Procedure
INFOID:0000000009722749
1.
CHECK SELF-DIAGNOSTIC RESULT-1
1.
Perform “Self-diagnostic result” of BCM using CONSULT.
2.
Erase DTC.
3.
Perform DTC Confirmation Procedure. Refer to
.
Is DTC 2195 detected?
YES
>> GO TO 2.
NO
>> INSPECTION END
2.
CHECK EQUIPMENT OF THE VEHICLE
Check that unspecified accessory part related to engine start is not installed.
Is unspecified accessory part related to engine start installed?
YES
>> GO TO 3.
NO
>> Replace BCM. Refer to
BCS-98, "Removal and Installation"
3.
CHECK SELF-DIAGNOSTIC RESULT-2
1.
Obtain the customers approval to remove unspecified accessory part related to engine start, and then
remove it.
2.
Perform “Self-diagnostic result” of BCM using CONSULT.
3.
Erase DTC.
4.
Perform DTC Confirmation Procedure. Refer to
.
Is DTC 2195 detected?
YES
>> Replace BCM. Refer to
BCS-98, "Removal and Installation"
NO
>> INSPECTION END
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2195
ANTI-SCANNING
ID verification between BCM and ECM that is out of
the specified specification is detected
ID verification request out of the
specified specification
SEC-50
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2555 STOP LAMP
B2555 STOP LAMP
Description
INFOID:0000000009722750
BCM detects the stop lamp status and confirms the stop lamp switch ON/OFF status. BCM confirms the
engine start condition according to the stop lamp switch ON/OFF status.
DTC Logic
INFOID:0000000009722751
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Depress the brake pedal and wait for at least 1 second.
2.
Check “Self diagnostic result” with CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009722752
1.
CHECK STOP LAMP SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check voltage between BCM harness connector and ground.
Is the inspection normal?
YES
>> GO TO 2.
NO-1
>> Check 10A fuse [No. 7, located in the fuse block (J/B)].
NO-2
>> Check harness for open or short between BCM and fuse.
2.
CHECK STOP LAMP SWITCH POWER SUPPLY CIRCUIT
1.
Disconnect stop lamp switch connector.
2.
Check voltage between stop lamp harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Check harness for open or short between stop lamp switch and fuse.
3.
CHECK STOP LAMP SWITCH CIRCUIT
DTC No.
Trouble diagno-
sis name
DTC detecting condition
Possible cause
B2555
STOP LAMP
BCM makes a comparison between the
upper voltage and lower voltage of stop
lamp switch. It judges from their values to
detect the malfunctioning circuit.
• Harness or connectors
(Stop lamp switch circuit is open or shorted)
• Stop lamp switch
• Fuse
(+)
(–)
Voltage (V)
(Approx.)
BCM
Connector
Terminal
M123
116
Ground
Battery voltage
(+)
(–)
Voltage (V)
(Approx.)
Stop lamp switch
Connector
Terminal
E116
1
Ground
Battery voltage
B2555 STOP LAMP
SEC-51
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
1.
Check continuity between stop lamp switch harness connector and BCM harness connector.
2.
Check continuity between stop lamp switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness or connector.
4.
CHECK STOP LAMP SWITCH
SEC-51, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace stop lamp switch. Refer to
BR-20, "Removal and Installation"
.
5.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000009722753
1.
CHECK STOP LAMP SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect stop lamp switch connector.
3.
Check continuity between stop lamp switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace stop lamp switch. Refer to
BR-20, "Removal and Installation"
.
Stop lamp switch
BCM
Continuity
Connector
Terminal
Connector
Terminal
E116
2
M123
118
Existed
Stop lamp switch
Ground
Continuity
Connector
Terminal
E116
2
Not existed
Stop lamp switch
Condition
Continuity
Terminal
1
2
Brake pedal
Not depressed
Not existed
Depressed
Existed
SEC-52
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2556 PUSH-BUTTON IGNITION SWITCH
B2556 PUSH-BUTTON IGNITION SWITCH
Description
INFOID:0000000009722754
The switch that changes the power supply position. BCM maintains the power supply position status. BCM
changes the power supply position with the operation of the push-button ignition switch.
DTC Logic
INFOID:0000000009722755
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start the engine and wait for at least 100 seconds.
2.
Check “Self diagnostic result” with CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009722756
1.
CHECK PUSH-BUTTON IGNITION SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect push-button ignition switch connector.
3.
Check voltage between push-button ignition switch harness connector and ground.
Is the inspection normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT
1.
Disconnect BCM connector and IPDM E/R connector.
2.
Check continuity between push-button ignition switch harness connector and BCM harness connector.
3.
Check continuity between push-button ignition switch harness connector and ground.
Is the inspection normal?
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2556
PUSH-BTN IGN SW
BCM detects the push-button ignition
switch stuck to ON for 100 seconds or
more
• Harness or connectors
(Push-button ignition switch circuit is shorted.)
• Push-button ignition switch
• BCM
(+)
(–)
Voltage (V)
(Approx.)
Push-button ignition switch
Connector
Terminal
M101
4
Ground
Battery voltage
Push-button ignition switch
BCM
Continuity
Connector
Terminal
Connector
Terminal
M101
4
M121
60
Existed
Push-button ignition switch
Ground
Continuity
Connector
Terminal
M101
4
Not existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст