Nissan Murano. Instruction — part 739
EXL-368
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
REAR COMBINATION LAMP
REAR COMBINATION LAMP
Exploded View
INFOID:0000000009723102
REMOVAL
DISASSEMBLY
Removal and Installation
INFOID:0000000009723103
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
1.
Remove the rear combination lamp finisher.
2.
Remove the rear combination lamp mounting bolts.
1.
Seal packing
2.
Rear combination lamp
3.
Rear combination lamp finisher
Refer to
for symbols in the figure.
JPLIA0821ZZ
1.
Rear turn signal lamp bulb
2.
Rear turn signal lamp bulb socket
3.
Rear side marker lamp bulb socket
4.
Rear side marker lamp bulb
JMLIA1741ZZ
REAR COMBINATION LAMP
EXL-369
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
3.
Pull the rear combination lamp toward outside of the vehicle
(
). Remove the rear combination lamp.
4.
Disconnect the rear combination lamp connector.
INSTALLATION
Install in the reverse order of removal.
Replacement
INFOID:0000000009723104
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
STOP/TAIL LAMP
Replacement integral with rear combination lamp. Refer to
REAR SIDE MARKER LAMP BULB
1.
Remove the rear combination lamp. Refer to
2.
Rotate the rear side marker lamp bulb socket counterclockwise, and unlock it.
3.
Remove the bulb from the rear side marker lamp bulb socket.
REAR TURN SIGNAL LAMP BULB
1.
Remove the rear combination lamp. Refer to
2.
Rotate the rear turn signal lamp bulb socket counterclockwise, and unlock it.
3.
Remove the bulb from the rear turn signal lamp bulb socket.
JPLIA1531ZZ
EXL-370
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
HIGH-MOUNTED STOP LAMP
HIGH-MOUNTED STOP LAMP
Exploded View
INFOID:0000000009723105
Removal and Installation
INFOID:0000000009723106
CAUTION:
Disconnect battery negative terminal or remove the fuse.
REMOVAL
1.
Remove the back door plate. Refer to
2.
Remove the high-mounted stop lamp mounting nuts and connector.
3.
Pull the high-mounted stop lamp toward rear of the vehicle. Remove the rear washer tube.
4.
Disconnect the high-mounted stop lamp connector.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Seal packing cannot be reused.
1.
Seal packing
2.
High-mounted stop lamp
Refer to
for symbols in the figure.
JPLIA0823ZZ
BACK-UP LAMP
EXL-371
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
BACK-UP LAMP
Exploded View
INFOID:0000000009723107
Removal and Installation
INFOID:0000000009723108
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
1.
Remove the back door finisher inner. Refer to
2.
Remove the back-up lamp mounting nuts and clip.
3.
Disconnect the back-up lamp connector. And then remove the back-up lamp.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Seal packing cannot be reused.
Replacement
INFOID:0000000009723109
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
BACK-UP LAMP BULB
1.
Remove the back-up lamp. Refer to
1.
Seal packing
2.
Back-up lamp
Refer to
JPLIA0824ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст