Nissan Murano. Instruction — part 444
C1204 AWD SOLENOID
DLN-15
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY20A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
2.
Check the continuity between AWD control unit harness connector and the ground.
3.
Check the continuity between AWD solenoid harness connector and the ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.
CHECK AWD SOLENOID
Check AWD solenoid. Refer to
DLN-15, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> AWD solenoid is malfunctioning. Replace electric controlled coupling. Refer to
5.
CHECK TERMINALS AND HARNESS CONNECTORS
1.
Check AWD control unit pin terminals for damage or loose connection with harness connector.
2.
Check AWD solenoid pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES
>> Replace AWD control unit. Refer to
NO
>> Repair or replace error-detected parts.
Component Inspection
INFOID:0000000009718087
1.
CHECK AWD SOLENOID
1.
Turn the ignition switch OFF.
2.
Disconnect AWD solenoid harness connector.
3.
Check the resistance between AWD solenoid harness connector terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> AWD solenoid is malfunctioning. Replace electric controlled coupling. Refer to
AWD control unit
AWD solenoid
Continuity
Connector
Terminal
Connector
Terminal
M69
1
C1
1
Existed
2
2
AWD control unit
—
Continuity
Connector
Terminal
M69
1
Ground
Not existed
2
AWD solenoid
—
Continuity
Connector
Terminal
C1
1
Ground
Not existed
2
AWD solenoid
Resistance (Approx.)
Terminal
1
2
2.45
Ω
DLN-16
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY20A]
C1205 AWD ACTUATOR RELAY
C1205 AWD ACTUATOR RELAY
Description
INFOID:0000000009718088
AWD solenoid is supplied with voltage by the internal circuit of AWD control unit.
DTC Logic
INFOID:0000000009718089
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
DTC REPRODUCTION PROCEDURE
With CONSULT
1.
Turn the ignition switch OFF to ON.
2.
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “C1205” detected?
YES
>> Proceed to diagnosis procedure. Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009718090
1.
CHECK AWD SOLENOID CIRCUIT (1)
1.
Turn the ignition switch OFF.
2.
Disconnect AWD control unit harness connector.
3.
Check the continuity between AWD control unit harness connector and the ground.
Is the inspection result normal?
YES >> GO TO 2.
NO
>> GO TO 3.
2.
CHECK TERMINALS AND HARNESS CONNECTORS
1.
Check AWD control unit pin terminals for damage or loose connection with harness connector.
2.
Check AWD solenoid pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES
>> After connecting each harness connector, perform DTC confirmation procedure again. When DTC
“C1205” is detected, replace AWD control unit. Refer to
NO
>> Repair or replace damaged parts.
3.
CHECK AWD SOLENOID
1.
Disconnect AWD solenoid harness connector.
2.
Check the continuity between AWD solenoid harness connector and the ground.
DTC
Display item
Malfunction detected condition
Possible cause
C1205
4WD ACTUATOR RLY
Malfunction has been detected from
AWD actuator relay integrated with AWD
control unit, or malfunction related to
AWD solenoid has been detected.
• Internal malfunction of AWD control
unit
• Malfunction of AWD solenoid power
supply circuit (open or short)
AWD control unit
—
Continuity
Connector
Terminal
M69
1
Ground
Not existed
2
C1205 AWD ACTUATOR RELAY
DLN-17
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY20A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> AWD solenoid is malfunctioning. Replace electric controlled coupling. Refer to
4.
CHECK AWD SOLENOID CIRCUIT
Check the continuity between AWD control unit harness connector and the ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace damaged parts.
5.
CHECK TERMINALS AND HARNESS CONNECTORS
1.
Check AWD control unit pin terminals for damage or loose connection with harness connector.
2.
Check AWD solenoid pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES
>> After connecting each harness connector, perform DTC confirmation procedure again. When DTC
“C1205” is detected, GO TO 1.
NO
>> Repair or replace damaged parts.
AWD solenoid
—
Continuity
Terminal
1
Ground
Not existed
2
AWD control unit
—
Continuity
Connector
Terminal
M69
1
Ground
Not existed
2
DLN-18
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY20A]
C1210 ECM
C1210 ECM
Description
INFOID:0000000009718091
Transmits the following signals via CAN communication to AWD control unit.
• Accelerator pedal position signal
• Engine speed signal
DTC Logic
INFOID:0000000009718092
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
DTC REPRODUCTION PROCEDURE
With CONSULT
1.
Start the engine. Drive the vehicle for a while.
2.
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “C1210” detected?
YES
>> Proceed to diagnosis procedure. Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009718093
1.
PERFORM ECM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ENGINE”.
Is any DTC detected?
YES
>> Check the DTC.
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
1.
Erase self-diagnostic results for “ALL MODE AWD/4WD”.
2.
Turn the ignition switch OFF.
3.
Start the engine. Drive the vehicle for a while.
4.
Stop the vehicle. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “C1210” detected?
YES
>> Replace AWD control unit. Refer to
NO
>> Check AWD control unit pin terminals for damage or loose connection with harness connector. If
any items are damaged, repair or replace error-detected parts.
DTC
Display item
Malfunction detected condition
Possible cause
C1210
ENGINE SIGNAL 1
Malfunction related to engine signal has
been detected.
Malfunction of engine control system
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст