Nissan Murano. Instruction — part 605
EC-530
< PREPARATION >
[VQ35DE]
PREPARATION
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000009720254
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
INFOID:0000000009720255
Tool number
(Kent-Moore No.)
Tool name
Description
(J-44321)
Fuel pressure gauge
kit
Checks fuel pressure
(J-44321-6)
Fuel pressure adapter
Connects fuel pressure gauge to quick connector
type fuel lines
LEC642
LBIA0376E
Tool name
(Kent-Moore No.)
Description
(J-45488)
Quick connector re-
lease
Removes fuel tube quick connectors in engine
room
Leak detector
i.e.: (J-41416)
Locates the EVAP leakage
EVAP service port
adapter
i.e.: (J-41413-OBD)
Applys positive pressure through EVAP service
port
PBIC0198E
S-NT703
S-NT704
PREPARATION
EC-531
< PREPARATION >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Fuel filler cap adapter
i.e.: (MLR-8382)
Checks fuel tank vacuum relief valve opening
pressure
Socket wrench
Removes and installs engine coolant temperature
sensor. Refer to
Oxygen sensor thread
cleaner
i.e.: (J-43897-18)
(J-43897-12)
Reconditions the exhaust system threads before
installing a new oxygen sensor. Use with anti-
seize lubricant shown below.
a: 18 mm diameter with pitch 1.5 mm for Zirco-
nia Oxygen Sensor
b: 12 mm diameter with pitch 1.25 mm for Tita-
nia Oxygen Sensor
Anti-seize lubricant
i.e.: (Permatex
TM
133AR or equivalent
meeting MIL specifica-
tion MIL-A-907)
Lubricates oxygen sensor thread cleaning tool
when reconditioning exhaust system threads.
Tool name
(Kent-Moore No.)
Description
S-NT815
S-NT705
AEM488
S-NT779
EC-532
< PERIODIC MAINTENANCE >
[VQ35DE]
FUEL PRESSURE
PERIODIC MAINTENANCE
FUEL PRESSURE
Inspection
INFOID:0000000009720256
FUEL PRESSURE RELEASE
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “FUEL PRESSURE RELEASE” in “WORK SUPPORT” mode with CONSULT.
3.
Start engine.
4.
After engine stalls, crank it 2 or 3 times to release all fuel pressure.
5.
Turn ignition switch OFF.
Without CONSULT
1.
Remove fuel pump fuse (2) located in IPDM E/R (1).
2.
Start engine.
3.
After engine stalls, crank it 2 or 3 times to release all fuel pres-
sure.
4.
Turn ignition switch OFF.
5.
Reinstall fuel pump fuse after servicing fuel system.
FUEL PRESSURE CHECK
CAUTION:
Before disconnecting fuel line, release fuel pressure from fuel line to eliminate danger.
NOTE:
• Prepare pans or saucers under the disconnected fuel line because the fuel may spill out. The fuel
pressure cannot be completely released because Z51 models do not have fuel return system.
• Be careful not to scratch or get the fuel hose connection area dirty when servicing, so that the quick
connector o-ring maintains seal ability.
• Use Fuel Pressure Gauge Kit [SST (J-44321)] and Fuel Pressure Adapter [SST (J-44321-6)] to check
fuel pressure.
1.
Release fuel pressure to zero.
2.
Remove fuel hose using Quick Connector Release [SST (J-45488)].
• Do not twist or kink fuel hose because it is plastic hose.
• Do not remove fuel hose (1) from quick connector.
• Keep fuel hose connections clean.
3.
Install Fuel Pressure Adapter [SST (J-44321-6)] (B) and Fuel
Pressure Gauge kit [SST (J44321)] (A) as shown in figure.
• Do not distort or bend fuel rail tube when installing fuel pres-
sure gauge adapter.
• When reconnecting fuel hose, check the original fuel hose for
damage and abnormality.
4.
Turn ignition switch ON (reactivate fuel pump) and check for fuel
leakage.
5.
Start engine and check for fuel leakage.
6.
Read the indication of fuel pressure gauge kit [SST (J-44321)].
• During fuel pressure check, check for fuel leakage from fuel
connection every 3 minutes.
JMBIA1659ZZ
At idling
: Approximately 350 kPa (3.57 kg/cm
2
, 51 psi)
JMBIA1127ZZ
FUEL PRESSURE
EC-533
< PERIODIC MAINTENANCE >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
7.
If result is unsatisfactory, go to next step.
8.
Check the following.
• Fuel hoses and fuel tubes for clogging
• Fuel filter for clogging
• Fuel pump
• Fuel pressure regulator for clogging
9.
If OK, replace fuel pressure regulator.
If NG, repair or replace malfunctioning part.
10. Before disconnecting Fuel Pressure Gauge kit [SST (J-44321)] and Fuel Pressure Adapter [SST (J-
44321-6)], release fuel pressure to zero.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст