Nissan Murano. Instruction — part 462
REAR PROPELLER SHAFT
DLN-87
< REMOVAL AND INSTALLATION >
[REAR PROPELLER SHAFT: 3F63A-EDJ75]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
- Install propeller shaft (1) while aligning its matching mark (A) with
the matching mark (B) of the final drive (2) on the joint as close as
possible.
- Tighten mounting bolts and nuts of propeller shaft and final drive to
the specified torque.
Inspection
INFOID:0000000009718170
INSPECTION AFTER REMOVAL
Appearance
Check propeller shaft for bend and damage. If damage is detected, replace propeller shaft assembly.
Propeller Shaft Runout
Check propeller shaft runout at measuring points with a dial indica-
tor. If runout exceeds specifications, replace propeller shaft assem-
bly.
• Propeller shaft runout measuring point (Point “ ”).
Journal Axial Play
As shown in the figure, while fixing yoke on one side, check axial
play of joint. If it is outside the standard, replace propeller shaft
assembly.
CAUTION:
Never disassemble joints.
Center Bearing
Check center bearing for noise and damage. If noise or damage is detected, replace propeller shaft assembly.
CAUTION:
Never disassemble center bearing.
JPDID0165ZZ
Propeller shaft runout
: Refer to
.
JPDID0158ZZ
: Vehicle front
Dimension
A: 506.5 mm (19.94 in)
B: 497.5 mm (19.59 in)
JPDID0156ZZ
Journal axial play
: Refer to
PDA0005D
DLN-88
< REMOVAL AND INSTALLATION >
[REAR PROPELLER SHAFT: 3F63A-EDJ75]
REAR PROPELLER SHAFT
INSPECTION AFTER INSTALLATION
After assembly, perform a driving test to check propeller shaft vibration. If vibration occurred, separate propel-
ler shaft from final drive or transfer. Reinstall companion flange by changing the phase between companion
flange and propeller shaft by the one bolt hole at a time. Then perform driving test and check propeller shaft
vibration again at each point.
SERVICE DATA AND SPECIFICATIONS (SDS)
DLN-89
< SERVICE DATA AND SPECIFICATIONS (SDS)
[REAR PROPELLER SHAFT: 3F63A-EDJ75]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specifications
INFOID:0000000009718171
Propeller Shaft Runout
INFOID:0000000009718172
Unit: mm (in)
Journal Axial Play
INFOID:0000000009718173
Unit: mm (in)
Applied model
AWD
VQ35DE
CVT
Propeller shaft model
3F63A-EDJ75
Number of joints
3
Type of journal bearings
(Non-disassembly type)
1st joint
Shell type
2nd joint
EDJ type
3rd joint
Shell type
Coupling method with transfer
Flange type
Coupling method with rear final drive
Flange type
Shaft length
1st (Spider to EDJ joint center)
1142 mm (44.96 in)
2nd (EDJ joint center to spider)
987 mm (38.86 in)
Shaft outer diameter
1st
63.5 mm (2.500 in)
2nd
75 mm (2.95 in)
Item
Limit
Propeller shaft runout
0.8 (0.031)
Item
Standard
Journal axial play
0 (0)
DLN-90
< SYSTEM DESCRIPTION >
[REAR FINAL DRIVE: R145]
REAR FINAL DRIVE ASSEMBLY
SYSTEM DESCRIPTION
REAR FINAL DRIVE ASSEMBLY
System Diagram
INFOID:0000000009718174
1.
Companion flange
2.
Electric controlled coupling
3.
AWD solenoid
4.
Center oil seal
5.
Pinion front bearing
6.
Collapsible spacer
7.
Pinion rear bearing
8.
Drive pinion
9.
Side gear
10. Pinion mate gear
11.
Drive gear
12. Pinion mate shaft
13. Side bearing
14. Differential case
JPDID0133ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст