Nissan Murano. Instruction — part 82
AV-106
< BASIC INSPECTION >
[BASE AUDIO WITH COLOR DISPLAY]
CONFIGURATION (AV CONTROL UNIT)
*: In the following table, find an illustration that the
part matches the vehicle and select microphone type.
MANUAL SETTING ITEM
Detail
Items
Setting value
STEERING
LHD
LHD models
RHD
RHD models
CAMERA SYSTEM
REAR CAMERA
With rear view monitor system
REAR+SIDE
With rear view monitor system and
front-side view monitor function
SOUND SYSTEM
BASE
Without BOSE system
BOSE
With BOSE system
MICROPHONE
DIRECTIONAL MIC
With directional microphone
*
NON-DIRECTIONAL MIC
With non-directional microphone
*
AFFORDABLE ITS
WITH
With BSW and LDW
WITHOUT
Without BSW and LDW
Directional microphone
Non-directional microphone
: Microphone installation position
: Microphone installation position
: Microphone installation position
: Microphone installation position
: Microphone installation position
: Microphone installation position
JSNIA5541ZZ
JSNIA5542ZZ
JSNIA5543ZZ
JSNIA5544ZZ
JSNIA5545ZZ
JSNIA5546ZZ
AV
U1000 CAN COMM CIRCUIT
AV-107
< DTC/CIRCUIT DIAGNOSIS >
[BASE AUDIO WITH COLOR DISPLAY]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
DTC/CIRCUIT DIAGNOSIS
U1000 CAN COMM CIRCUIT
Description
INFOID:0000000009721618
CAN (Controller Area Network) is a serial communication line for real-time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independently). In CAN communication, control units are connected with 2
communication lines (CAN-H, CAN-L) allowing a high rate of information transmission with less wiring. Each
control unit transmits/receives data but selectively reads required data only.
CAN Communication Signal Chart. Refer to
LAN-29, "CAN Communication Signal Chart"
DTC Logic
INFOID:0000000009721619
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000009721620
1.
PERFORM SELF-DIAGNOSTIC
1.
Turn ignition switch ON and wait for 2 seconds or more.
2.
Check “Self Diagnostic Result” of “MULTI AV”.
Is “CAN COMM CIRCUIT” displayed?
YES
>> Refer to
LAN-18, "Trouble Diagnosis Procedure"
.
NO
>> Refer to
GI-44, "Intermittent Incident"
.
DTC
Display contents of CON-
SULT
DTC detection condition
Probable malfunction location
U1000
CAN COMM CIRCUIT
[U1000]
AV control unit is not transmitting or receiving
CAN communication signal for 2 seconds or
more.
CAN communication system.
AV-108
< DTC/CIRCUIT DIAGNOSIS >
[BASE AUDIO WITH COLOR DISPLAY]
U1010 CONTROL UNIT (CAN)
U1010 CONTROL UNIT (CAN)
DTC Logic
INFOID:0000000009721621
DTC DETECTION LOGIC
DTC
Display contents of CON-
SULT
DTC detection condition
Probable malfunction factor
U1010
CONTROL UNIT (CAN)
[U1010]
CAN initial diagnosis malfunction is detected.
Replace the AV control unit if the malfunction
occurs constantly.
Refer to
AV
U1200 AV CONTROL UNIT
AV-109
< DTC/CIRCUIT DIAGNOSIS >
[BASE AUDIO WITH COLOR DISPLAY]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
U1200 AV CONTROL UNIT
DTC Logic
INFOID:0000000009721622
DTC
Display contents of
CONSULT
DTC detection condition
Possible malfunction factor
U1200
Cont Unit
[U1200]
AV control unit malfunction is detected.
Replace the AV control unit if the mal-
function occurs constantly.
Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст