Nissan Murano. Instruction — part 209
BR-46
< REMOVAL AND INSTALLATION >
FRONT DISC BRAKE
4.
Apply brake fluid to pistons (1). Push piston into cylinder body
by hand and push piston boot (2) piston-side lip into the piston
groove.
CAUTION:
Press the piston evenly and vary the pressing point to pre-
vent cylinder inner wall from being rubbed.
5.
Apply rubber grease to bushing, install bushing to sliding pin.
6.
Apply rubber grease to sliding pins and sliding pin boots, install
sliding pins and sliding pin boots to torque member.
7.
Install the cylinder body to the torque member and tighten the
sliding pin bolts to the specified torque.
BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) : Inspection
INFOID:0000000009722347
INSPECTION AFTER DISASSEMBLY
Cylinder Body
Check the inner wall of the cylinder for rust, wear, cracks or damage. Replace the cylinder if any abnormal
condition is detected.
CAUTION:
Always clean with new brake fluid. Never clean with mineral oil such as gasoline and light oil.
Torque Member
Check the torque member for rust, wear, cracks or damage. Replace the member if any abnormal condition is
detected.
Pistons
Check the surface of the piston for rust, wear, cracks or damage. Replace the piston if any abnormal condition
is detected.
CAUTION:
A piston sliding surface is plated. Never polish with sandpaper.
Sliding Pin and Sliding Pin Boot
Check the sliding pins and sliding boots for rust, wear, cracks or damage. Replace the parts if any abnormal
condition is detected.
INSPECTION AFTER INSTALLATION
1.
Check a drag of front disc brake. If any drag is found, follow the procedure described below.
2.
Remove brake pads.
3.
Press the piston.
CAUTION:
• Never damage the piston boot.
• When replacing a pad with new one, check a brake fluid level in the reservoir tank because brake
fluid returns to master cylinder reservoir tank when pressing piston in.
NOTE:
Use a disc brake piston tool to easily press piston.
4.
Install brake pads.
5.
Depress the brake pedal several times.
6.
Check a drag of front disc brake again. If any drag is found, disassemble the cylinder body. Refer to
44, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) : Disassembly and Assembly"
.
7.
Burnish contact surfaces after refinishing or replacing disc rotors, or if a soft pedal occurs at very low mile-
age. Refer to
BR-16, "DISC ROTOR : Inspection and Adjustment"
JPFIA0034ZZ
REAR DISC BRAKE
BR-47
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
REAR DISC BRAKE
BRAKE PAD
BRAKE PAD : Exploded View
INFOID:0000000009722348
BRAKE PAD : Removal and Installation
INFOID:0000000009722349
REMOVAL
WARNING:
Since dust covering the rear brake has an affect on human body, the dust must be removed with a
dust collector. Never splatter the dust with an air blow gun.
CAUTION:
• Never depress the brake pedal while removing the brake pads or the cylinder body because the pis-
ton may pop out.
• Never spill or splash brake fluid on the disc rotor.
1.
Remove tires with power tool.
2.
Remove the upper sliding pin bolt.
3.
Suspend the cylinder body with suitable wire so that the brake hose will not stretch. Remove the brake
pads, shims and shim cover from the torque member.
CAUTION:
• Never deform the pad retainers if removing the pad retainers.
• Never damage the piston boot.
• Never drop the brake pad, shims, and the shim cover.
• Remember each position of the removed brake pads.
INSTALLATION
WARNING:
Since dust covering the rear brake has an affect on human body, the dust must be removed with a
dust collector. Never splatter the dust with an air blow gun.
1.
Sliding pin bolt
2.
Cylinder body
3.
Inner shim cover
4.
Inner shim
5.
Inner pad (with pad wear sensor)
6.
Pad retainer
7.
Torque member
8.
Outer pad
9.
Outer shim
10.
Outer shim cover
1: Apply rubber grease.
2: Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease.
Refer to
for symbols not described on the above.
JPFIA0310GB
BR-48
< REMOVAL AND INSTALLATION >
REAR DISC BRAKE
CAUTION:
• Never depress the brake pedal while removing the brake pads or the cylinder body because the pis-
ton may pop out.
• Never spill or splash brake fluid on the disc rotor.
1.
Install the pad retainers to the torque member if the pad retainers has been removed.
CAUTION:
• Securely assemble the pad retainers not to be lifted up from the torque member.
• Never deform the pad retainers.
2.
Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease to the mating faces between the brake
pads, the shims and pawls part of cylinder body, and install them to the brake pad.
CAUTION:
Always replace the shims together with the shim cover when replacing the brake pad.
3.
Install cylinder body and brake pads to torque member.
CAUTION:
• Never damage the piston boot.
• When replacing pads with new one, check a brake fluid level in the reservoir tank because brake
fluid returns to master cylinder reservoir tank when pressing piston in.
NOTE:
Use a disc brake piston tool to easily press piston.
4.
Install the upper sliding pin bolt and tighten it to the specified torque.
5.
Depress the brake pedal several times to check that no drag feel is present for the rear disc brake. Refer
to
BR-48, "BRAKE PAD : Inspection"
.
BRAKE PAD : Inspection
INFOID:0000000009722350
INSPECTION AFTER REMOVAL
Replace the shims and the shim cover if rust is excessively attached.
INSPECTION AFTER INSTALLATION
1.
Check a drag of rear disc brake. If any drag is found, follow the procedure described below.
2.
Remove brake pads.
3.
Press the piston.
CAUTION:
• Never damage the piston boot.
• When replacing a pad with new one, check a brake fluid level in the reservoir tank because brake
fluid returns to master cylinder reservoir tank when pressing piston in.
NOTE:
Use a disc brake piston tool to easily press piston.
4.
Install brake pads.
5.
Depress the brake pedal several times.
6.
Check a drag of rear disc brake again. If any drag is found, disassemble the cylinder body. Refer to
50, "BRAKE CALIPER ASSEMBLY : Disassembly and Assembly"
.
7.
Burnish contact surfaces after refinishing or replacing pads, or if a soft pedal occurs at very low mileage.
Refer to
BR-18, "BRAKE PAD : Inspection and Adjustment"
.
BRAKE CALIPER ASSEMBLY
BRAKE CALIPER ASSEMBLY : Exploded View
INFOID:0000000009722351
REMOVAL
REAR DISC BRAKE
BR-49
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
DISASSEMBLY
BRAKE CALIPER ASSEMBLY : Removal and Installation
INFOID:0000000009722352
REMOVAL
WARNING:
1.
Brake caliper assembly
Refer to
for symbols not described on the above.
JPFIA0311GB
1.
Sliding pin bolt
2.
Bushing
3.
Cap
4.
Bleeder valve
5.
Cylinder body
6.
Piston seal
7.
Piston
8.
Piston boot
9.
Sliding pin boot
10. Torque member
1: Apply rubber grease.
2: Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease.
3: Apply polyglycol ether based lubricant.
: Apply brake fluid.
Refer to
for symbols not described on the above.
JPFIA0312GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст