Nissan Murano. Instruction — part 489
EC-66
< SYSTEM DESCRIPTION >
[VQ35DE]
AUTOMATIC SPEED CONTROL DEVICE (ASCD)
AUTOMATIC SPEED CONTROL DEVICE (ASCD)
System Diagram
INFOID:0000000009719838
System Description
INFOID:0000000009719839
INPUT/OUTPUT SIGNAL CHART
*: This signal is sent to the ECM via the CAN communication line
BASIC ASCD SYSTEM
Refer to Owner's Instruction for ASCD operating instructions.
Automatic Speed Control Device (ASCD) allows a driver to keep vehicle at predetermined constant speed
without depressing accelerator pedal. Driver can set vehicle speed in advance between approximately 40 km/
h (25 MPH) and 144 km/h (89 MPH).
ECM controls throttle angle of electric throttle control actuator to regulate engine speed.
Operation status of ASCD is indicated by CRUISE on combination meter. If any malfunction occurs in the
ASCD system, it automatically deactivates control.
NOTE:
Always drive vehicle in a safe manner according to traffic conditions and obey all traffic laws.
SET OPERATION
Press MAIN switch. (The CRUISE on combination meter illuminates.)
When vehicle speed reaches a desired speed between approximately 40 km/h (25 MPH) and 144 km/h (89
MPH), press SET/COAST switch.
ACCELERATE OPERATION
If the RESUME/ACCELERATE switch is pressed during cruise control driving, increase the vehicle speed until
the switch is released or vehicle speed reaches maximum speed controlled by the system.
And then ASCD will maintain the new set speed.
CANCEL OPERATION
When any of following conditions exist, cruise operation will be canceled.
• CANCEL switch is pressed
• More than 2 switches on ASCD steering switch are pressed at the same time (Set speed will be cleared)
• Brake pedal is depressed
JMBIA1826GB
Sensor
Input signal to ECM
ECM function
Actuator
ASCD brake switch
Brake pedal operation
ASCD vehicle speed control
Electric throttle control
actuator
Stop lamp switch
Brake pedal operation
ASCD steering switch
ASCD steering switch operation
TCM
Gear position
Powertrain revolution*
Combination meter
Vehicle speed*
AUTOMATIC SPEED CONTROL DEVICE (ASCD)
EC-67
< SYSTEM DESCRIPTION >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
• Selector lever position changed to N, P or R
• Vehicle speed decreased to 13 km/h (8 MPH) lower than the set speed
• TCS system is operated
• CVT control system has a malfunction. Refer to
• Engine coolant temperature is slightly higher than the normal operating temperature
When the ECM detects any of the following conditions, the ECM will cancel the cruise operation and inform
the driver by blinking indicator lamp.
• Malfunction for some self-diagnoses regarding ASCD control: CRUISE will blink quickly.
If MAIN switch is turned to OFF while ASCD is activated, all of ASCD operations will be canceled and vehicle
speed memory will be erased.
COAST OPERATION
When the SET/COAST switch is pressed during cruise control driving, decrease vehicle set speed until the
switch is released. And then ASCD will maintain the new set speed.
RESUME OPERATION
When the RESUME/ACCELERATE switch is pressed after canceling operation other than pressing the MAIN
switch is performed, vehicle speed will return to last set speed. To resume vehicle set speed, vehicle condition
must meet following conditions.
• Brake pedal is released
• Selector lever position is other than P and N
• Vehicle speed is greater than 40 km/h (25 MPH) and less than 144 km/h (89 MPH)
Component Parts Location
INFOID:0000000009719840
JMBIA1108ZZ
EC-68
< SYSTEM DESCRIPTION >
[VQ35DE]
AUTOMATIC SPEED CONTROL DEVICE (ASCD)
1.
Intake valve timing control solenoid
valve (bank 1)
2.
Intake valve timing control solenoid
valve (bank 2)
3.
Electronic controlled engine mount
control solenoid valve
4.
Fuel injector (bank 2)
5.
A/F sensor 1 (bank 2)
6.
Cooling fan motor-2
7.
Ignition coil (with power transistor)
and spark plug (bank 2)
8.
Camshaft position sensor (PHASE)
(bank 2)
9.
Crankshaft position sensor (POS)
10. Engine coolant temperature sensor
11.
Cooling fan motor-1
12. ECM
13. Refrigerant pressure sensor
14. Battery current sensor
15. IPDM E/R
16. Mass air flow sensor (with intake air
temperature sensor)
17. Electric throttle control actuator
18. EVAP service port
19. Power valve actuator 2
20. EVAP canister purge volume control
solenoid valve
21. Camshaft position sensor (PHASE)
(bank 1)
22. Ignition coil (with power transistor)
and spark plug (bank 1)
23. A/F sensor 1 (bank 1)
24. Fuel injector (bank 1)
25. VIAS control solenoid valve 1 and 2
26. Power valve actuator 1
1.
Mas air flow sensor (with intake air
temperature sensor)
2.
Electric throttle control actuator
: Vehicle front
1.
Ignition coil (with power transistor)
and spark plug (bank 1)
2.
Fuel injector (bank 1)
3.
Fuel injector (bank 2)
4.
Ignition coil (with power transistor)
and spark plug (bank 2)
5.
Knock sensor (bank 2)
6.
Knock sensor (bank 1)
: Vehicle front
JMBIA1109ZZ
JMBIA1110ZZ
AUTOMATIC SPEED CONTROL DEVICE (ASCD)
EC-69
< SYSTEM DESCRIPTION >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
1.
Crankshaft position sensor (POS)
2.
Camshaft position sensor (PHASE)
(bank 1)
3.
Camshaft position sensor (PHASE)
(bank 2)
: Vehicle front
1.
Cooling fan motor-1
2.
Cooling fan motor-1 harness con-
nector
3.
Cooling fan motor-1 harness con-
nector
4.
Cooling fan motor-2
5.
Engine coolant temperature sensor
: Vehicle front
1.
Refrigerant pressure sensor
2.
Battery current sensor
: Vehicle front
JMBIA1114ZZ
JMBIA1112ZZ
JMBIA1113ZZ
JMBIA1115ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст