Nissan Murano. Instruction — part 653
EXL-24
< SYSTEM DESCRIPTION >
[XENON TYPE]
DIAGNOSIS SYSTEM (BCM)
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000010092627
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
NOTE:
• *1: For models with rain sensor this mode is displayed, but is not used.
• *2: This item is displayed, but is not used.
FREEZE FRAME DATA (FFD)
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
*
1
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
×
—
AIR CONDITONER*
2
• Intelligent Key system
• Engine start system
INTELLIGENT KEY
×
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NVIS - NATS
IMMU
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Back door opener system
TRUNK
×
×
Vehicle security system
THEFT ALM
×
×
×
RAP system
RETAINED PWR
×
Signal buffer system
SIGNAL BUFFER
×
×
TPMS
TPMS (AIR PRESSURE MONITOR)
×
×
×
DIAGNOSIS SYSTEM (BCM)
EXL-25
< SYSTEM DESCRIPTION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT.
NOTE:
*: Power supply position shifts to “LOCK” from “OFF”, when ignition switch is in the OFF position, selector lever is in the P position, and
any of the following conditions are met.
• Closing door
• Opening door
• Door is locked using door request switch
• Door is locked using Intelligent Key
The power supply position shifts to “ACC” when the push-button ignition switch (push switch) is pushed at “LOCK”.
HEADLAMP
HEADLAMP : CONSULT Function (BCM - HEAD LAMP)
INFOID:0000000009722893
WORK SUPPORT
CONSULT screen item
Indication/Unit
Description
Vehicle Speed
km/h
Vehicle speed of the moment a particular DTC is detected
Odo/Trip Meter
km
Total mileage (Odometer value) of the moment a particular DTC is detected
Vehicle Condition
SLEEP>LOCK
Power position status of
the moment a particular
DTC is detected
While turning BCM status from low power consumption mode to
normal mode (Power supply position is “LOCK”*)
SLEEP>OFF
While turning BCM status from low power consumption mode to
normal mode (Power supply position is “OFF”.)
LOCK>ACC
While turning power supply position from “LOCK” to “ACC”
ACC>ON
While turning power supply position from “ACC” to “IGN”
RUN>ACC
While turning power supply position from “RUN” to “ACC” (Vehicle
is stopping and selector lever is except P position.)
CRANK>RUN
While turning power supply position from “CRANKING” to “RUN”
(From cranking up the engine to run it)
RUN>URGENT
While turning power supply position from “RUN“ to “ACC” (Emer-
gency stop operation)
ACC>OFF
While turning power supply position from “ACC” to “OFF”
OFF>LOCK
While turning power supply position from “OFF” to “LOCK”*
OFF>ACC
While turning power supply position from “OFF” to “ACC”
ON>CRANK
While turning power supply position from “IGN” to “CRANKING”
OFF>SLEEP
While turning BCM status from normal mode (Power supply posi-
tion is “OFF”.) to low power consumption mode
LOCK>SLEEP
While turning BCM status from normal mode (Power supply posi-
tion is “LOCK”*) to low power consumption mode
LOCK
Power supply position is “LOCK”*
OFF
Power supply position is “OFF” (Ignition switch OFF)
ACC
Power supply position is “ACC” (Ignition switch ACC)
ON
Power supply position is “IGN” (Ignition switch ON with engine
stopped)
ENGINE RUN
Power supply position is “RUN” (Ignition switch ON with engine
running)
CRANKING
Power supply position is “CRANKING” (At engine cranking)
IGN Counter
0 - 39
The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
• The number increases like 1
→
2
→
3...38
→
39 after returning to the normal condition
whenever ignition switch OFF
→
ON.
• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
EXL-26
< SYSTEM DESCRIPTION >
[XENON TYPE]
DIAGNOSIS SYSTEM (BCM)
*: Factory setting
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Service item
Setting item
Setting
BATTERY SAVER SET
On*
With the exterior lamp battery saver function
Off
Without the exterior lamp battery saver function
ILL DELAY SET
MODE 1*
45 sec.
Sets delay timer function timer operation time.
(All doors closed)
MODE 2
Without the func-
tion
MODE 3
30 sec.
MODE 4
60 sec.
MODE 5
90 sec.
MODE 6
120 sec.
MODE 7
150 sec.
MODE 8
180 sec.
CUSTOM A/LIGHT SET-
TING
MODE 1*
Normal
MODE 2
More sensitive setting than normal setting (Turns ON earlier than normal operation.)
MODE 3
More sensitive setting than MODE 2 (Turns ON earlier than MODE 2.)
MODE 4
Less sensitive setting than normal setting (Turns ON later than normal operation.)
Monitor item
[Unit]
Description
PUSH SW
[On/Off]
The switch status input from push-button ignition switch
ENGINE STATE
[Stop/Stall/Crank/Run]
The engine status received from ECM with CAN communication
VEH SPEED 1
[km/h]
The value of the vehicle speed received from combination meter with CAN commu-
nication
KEY SW-SLOT
[On/Off]
Key switch status input from key slot
TURN SIGNAL R
[On/Off]
Each switch status that BCM detects from the combination switch reading function
TURN SIGNAL L
[On/Off]
TAIL LAMP SW
[On/Off]
HI BEAM SW
[On/Off]
HEAD LAMP SW1
[On/Off]
HEAD LAMP SW2
[On/Off]
PASSING SW
[On/Off]
AUTO LIGHT SW
[On/Off]
FR FOG SW
[On/Off]
DIAGNOSIS SYSTEM (BCM)
EXL-27
< SYSTEM DESCRIPTION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
ACTIVE TEST
FLASHER
FLASHER : CONSULT Function (BCM - FLASHER)
INFOID:0000000009722894
WORK SUPPORT
RR FOG SW
[On/Off]
NOTE:
The item is indicated, but not monitored.
DOOR SW-DR
[On/Off]
The switch status input from front door switch (driver side)
DOOR SW-AS
[On/Off]
The switch status input from front door switch (passenger side)
DOOR SW-RR
[On/Off]
The switch status input from rear door switch RH
DOOR SW-RL
[On/Off]
The switch status input from rear door switch LH
DOOR SW-BK
[On/Off]
NOTE:
The item is indicated, but not monitored.
OPTICAL SENSOR
[V]
The value of exterior brightness voltage input from the optical sensor
Monitor item
[Unit]
Description
Test item
Operation
Description
TAIL LAMP
On
Transmits the position light request signal to IPDM E/R with CAN com-
munication to turn the tail lamp ON.
Off
Stops the position light request signal transmission.
HEAD LAMP
Hi
Transmits the high beam request signal with CAN communication to turn
the headlamp (HI).
Low
Transmits the low beam request signal with CAN communication to turn
the headlamp (LO).
Off
Stops the high & low beam request signal transmission.
FR FOG LAMP
On
Transmits the front fog light request signal to IPDM E/R with CAN com-
munication to turn the front fog lamp ON.
Off
Stops the front fog light request signal transmission.
RR FOG LAMP
On
NOTE:
The item is indicated, but cannot be tested.
Off
DAYTIME RUNNING LIGHT
On
NOTE:
The item is indicated, but cannot be tested.
Off
CORNERING LAMP
RH
NOTE:
The item is indicated, but cannot be tested.
LH
Off
ILL DIM SIGNAL
On
NOTE:
The item is indicated, but cannot be tested.
Off
Service item
Setting item
Setting
HAZARD ANSWER
BACK
Lock Only*
With locking only
Sets the hazard warning lamp answer back function
when the door is lock/unlock with the request switch or
the key fob.
Unlk Only
With unlocking only
Lock/Unlk
With locking/unlocking
Off
Without the function
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст