Nissan GT-R. Instruction — part 114
EXT-10
< PRECAUTION >
PRECAUTIONS
• Corrosion occurs to aluminum die-casting parts by the stray current corrosion phenomenon, when directly
contacting other parts made of steel. Always apply anti-stray current corrosion paint (primer) on the mount-
ing surface.
• Clean mounting surface to prevent any foreign matter, steel powder or others from being mixed in. Always
apply the specified adhesive when installing.
• Corrosion by stray current corrosion may occur when installing with any other bolts than the specified bolt.
Always use the specified bolt that is surface treated.
• When loosening the specified bolt that is tightened, the treated surface may peel. Never reuse the specified
bolt that is tightened once.
TIGHTENING TORQUE CONTROL
Material made of aluminum die-casting parts is soft in term of hardness. Tightening torque must be controlled
exactly as specified. Always use a torque wrench to install any part to the specified tightening torque.
WARNING:
Never use a power tool to remove or tighten bolts for aluminum die-casting part to prevent damage to
aluminum die-casting parts.
Precautions Necessary for Steering Wheel Rotation After Battery Disconnection
INFOID:0000000009161547
CAUTION:
Comply with the following cautions to prevent any error and malfunction.
• Before removing and installing any control units, first turn the ignition switch to the LOCK position,
then disconnect both battery cables.
• After finishing work, confirm that all control unit connectors are connected properly, then re-connect
both battery cables.
• Always use CONSULT to perform self-diagnosis as a part of each function inspection after finishing
work. If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
For vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock and
cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the operation pro-
cedure below before starting the repair operation.
OPERATION PROCEDURE
1.
Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2.
Turn the ignition switch to ACC position.
(At this time, the steering lock will be released.)
3.
Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
4.
Perform the necessary repair operation.
5.
When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the ignition switch from ACC position to ON position, then to LOCK position. (The steering wheel will lock
when the ignition switch is turned to LOCK position.)
6.
Perform self-diagnosis check of all control units using CONSULT.
Precaution for Battery Service
INFOID:0000000009161548
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.
PRECAUTIONS
EXT-11
< PRECAUTION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Precaution for Procedure without Cowl Top Cover
INFOID:0000000009161549
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.
Precaution for Work
INFOID:0000000009161550
• After removing and installing the opening/closing parts, be sure to carry out fitting adjustments to check their
operation.
• Check the lubrication level, damage, and wear of each part. If necessary, grease or replace it.
PIIB3706J
EXT-12
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000009161551
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
INFOID:0000000009161552
Tool number
(Kent-Moore No.)
Tool name
Description
(J-39570)
Chassis ear
Locates the noise
(J-43980)
NISSAN Squeak and Rattle
Kit
Repairs the cause of noise
SIIA0993E
SIIA0994E
Tool name
Description
Engine ear
Locates the noise
Remover tool
Removes clips, pawls and metal clips
SIIA0995E
JMKIA3050ZZ
PREPARATION
EXT-13
< PREPARATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Power tool
Hand nut rivet setter
Install bumper side bracket and license plate
Tool name
Description
PIIB1407E
JMKIA3000ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст