Nissan GT-R. Instruction — part 205
MA-42
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
Adjust the fluid level to the R level (B) rather than the fluid
level (A) in sports driving mode or in high road driving
mode.
3.
Fluid levels at HOT and COLD are different. Do not confuse
them.
CAUTION:
• The fluid level must not exceed the MAX line. Excessive fluid causes fluid leakage from the cap.
• Never reuse drained power steering fluid.
FLUID LEAKAGE
Check hydraulic connections for fluid leakage, cracks, damage,
looseness, or wear.
1.
Run the engine until the fluid temperature reaches 50 to 80
°
C
(122 to 176
°
F) in reservoir tank, and keep engine speed idle.
2.
Turn steering wheel several times from full left stop to full right
stop.
3.
Hold steering wheel at each lock position for five seconds and
carefully check for fluid leakage.
CAUTION:
Never hold the steering wheel in a locked position for more
than 10 seconds. (There is the possibility that power steer-
ing oil pump assembly may be damaged.)
4.
If fluid leakage at connections occurs, loosen flare nut and then retighten. Do not overtighten connector as
this can damage O-ring, washer and connector.
5.
If fluid leakage from oil pump occurs, check oil pump.
6.
Check steering gear boots for accumulation of fluid leakage from steering gear.
AXLE AND SUSPENSION PARTS
AXLE AND SUSPENSION PARTS : Inspection
INFOID:0000000009161798
Check front and rear axle and suspension parts for excessive play,
cracks, wear or other damage.
• Shake each wheel to check for excessive play.
• Check wheel bearings for smooth operation.
• Check axle and suspension nuts and bolts for looseness.
• Check strut (shock absorber) for oil leakage or other damage.
• Check suspension ball joint for grease leakage and ball joint dust
cover for cracks or other damage.
HOT
: Fluid temperature 50 – 80
°
C (122 – 176
°
F)
COLD
: Fluid temperature 0 – 30
°
C (32 – 86
°
F)
Recommended fluid
: Refer to
.
Fluid capacity
: Refer to
.
NNGIA0026GB
SGIA0506E
SMA525A
CHASSIS MAINTENANCE
MA-43
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
DRIVE SHAFT
DRIVE SHAFT : Inspection
INFOID:0000000009161799
Check boot and drive shaft for cracks, wear, damage and grease
leakage.
SFA392B
SFA108A
MA-44
< PERIODIC MAINTENANCE >
BODY MAINTENANCE
BODY MAINTENANCE
LOCKS, HINGES AND HOOD LATCH
LOCKS, HINGES AND HOOD LATCH : Lubricating
INFOID:0000000009161800
For hood and hood lock illustration. Refer to
DLK-128, "HOOD ASSEMBLY : Exploded View"
For trunk lid illustration. Refer to
DLK-144, "TRUNK LID ASSEMBLY : Exploded View"
.
SEAT BELT, BUCKLES, RETRACTORS, ANCHORS AND ADJUSTERS
SEAT BELT, BUCKLES, RETRACTORS, ANCHORS AND ADJUSTERS : Inspection
INFOID:0000000009161801
For front seat belt illustration. Refer to
SB-6, "SEAT BELT RETRACTOR : Exploded View"
For rear seat belt illustration. Refer to
SB-11, "SEAT BELT RETRACTOR : Exploded View"
CAUTION:
• After any collision, inspect all seat belt assemblies, including retractors and other attached hard-
wares (I.e. anchor bolt, guide rail set). Nissan recommends to replace all seat belt assemblies in use
during a collision, unless not damaged and properly operating after minor collision.
Also inspect seat belt assemblies not in use during a collision, and replace if damaged or improperly
operating.
Seat belt pre-tensioner should be replaced even if the seat belts are not in use during a frontal colli-
sion where the driver and passenger air bags are deployed.
• If any component of seat belt assembly is questionable, do not repair.
Replace as seat belt assembly.
• If webbing is cut, frayed, or damaged, replace belt assembly.
• Never oil tongue and buckle.
• Use a genuine NISSAN seat belt assembly.
For details, refer to
SB-4, "SEAT BELT RETRACTOR : Inspection"
SB-9, "SEAT BELT RETRACTOR : Inspec-
in SB section.
• Check anchors for loose mounting
• Check belts for damage
• Check retractor for smooth operation
• Check function of buckles and tongues when buckled and released
SERVICE DATA AND SPECIFICATIONS (SDS)
MA-45
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
DRIVE BELT
DRIVE BELT : Drive Belt (GT-R certified NISSAN dealer)
INFOID:0000000009161802
DRIVE BELT
ENGINE COOLANT
ENGINE COOLANT : Periodical Maintenance Specification
INFOID:0000000009161803
ENGINE COOLANT CAPACITY (APPROXIMATELY)
Unit:
(US qt, Imp qt)
ENGINE OIL
ENGINE OIL : Periodical Maintenance Specification
INFOID:0000000009161804
ENGINE OIL CAPACITY (APPROXIMATELY)
Unit:
(US qt, lmp qt)
SPARK PLUG
SPARK PLUG : Spark Plug
INFOID:0000000009161805
SPARK PLUG
Unit: mm (in)
ROAD WHEEL
ROAD WHEEL : Road Wheel (GT-R certified NISSAN dealer)
INFOID:0000000009161806
Tension of drive belt
Belt tension is not necessary, as it is automatically adjusted by drive belt auto-tensioner.
Engine coolant capacity [With reservoir tank (Between MIN and MAX level)]
11.3 (12, 10)
Reservoir tank engine coolant capacity (Between MIN and MAX level)
1.2 (1-1/4, 1)
Drain and refill
With oil filter change
5.0 (5-1/4, 4-3/8)
Without oil filter change
4.5 (4-3/4, 4)
Dry engine (Overhaul)
6.2 (6-4/8, 5-4/8)
Make
NGK
Standard type
DILKAR8A8
Gap (Nominal)
Standard
0.7 - 0.8 (0.028 - 0.031)
Limit
1.0 (0.039)
Item
Limit
Radial runout
Lateral deflection
Less than 0.3 mm (0.012 in)
Vertical deflection
Allowable unbalance
Dynamic (At flange)
Less than 5 g (0.17 oz) (one side)
Static (At flange)
Less than 10 g (0.35 oz)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст