Nissan GT-R. Instruction — part 95
EM-28
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Spark Plug
INFOID:0000000009162879
SPARK PLUG
Unit: mm (in)
Make
NGK
Standard type
DILKAR8A8
Gap (Nominal)
Standard
0.7 - 0.8 (0.028 - 0.031)
Limit
1.0 (0.039)
EX-1
ENGINE
C
D
E
F
G
H
I
J
K
L
M
SECTION
EX
A
EX
N
O
P
CONTENTS
EXHAUST SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Working Range at a Regular Deal-
ership . . . . . . . . . . . . . . . . . ....
Aluminum Die-Casting Parts Handling . . . . . ..
REMOVAL AND INSTALLATION . . . .
EXHAUST SYSTEM . . . . . . . . . . ...
EX-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Working Range at a Regular Dealership
INFOID:0000000009164429
CAUTION:
The service items unmentioned on this instruction are recommended to be performed by a GT-R certified
NISSAN dealer. Because those service items require special equipment and a GT-R certified technical
staff who completed special training.
Aluminum Die-Casting Parts Handling
INFOID:0000000009161454
PROHIBITION OF WELDING OR BEATING REPAIR
• Material made of aluminum die-casting parts is heat-treated and looses strength when being exposed to
welding heat. Do not perform welding repair for cracks, damage or others.
• For aluminum die-casting parts deformation, do not perform repair by beating. Always repair by replacement
as an assembly.
CRACK CHECK
When the vehicle is damaged, always perform a visual deformation check and a crack check.
Crack Check Procedures
For a crack check, use dye penetrant inspection fluid (pre-cleaning fluid, penetrant fluid and developer fluid).
CAUTION:
Always perform a crack check in accordance with the procedures specified by the manufacturer of the
dye penetrant inspection fluid.
1.
Spray pre-cleaning fluid on the checking surface for cleaning.
2.
Spray penetrant fluid on the checking surface and wait until the penetrant fluid soaks into any cracks.
3.
Wipe off excessive penetrant fluid, and then also lightly wipe off penetrant fluid using a wet cloth.
4.
Spray developer fluid on the checking surface.
5.
Cracks, if any, are dyed red in color.
STRAY CURRENT CORROSION
• Corrosion occurs to aluminum die-casting parts by the stray current corrosion phenomenon, when directly
contacting other parts made of steel. Always apply anti-stray current corrosion paint (primer) on the mount-
ing surface.
• Clean mounting surface to prevent any foreign matter, steel powder or others from being mixed in. Always
apply the specified adhesive when installing.
• Corrosion by stray current corrosion may occur when installing with any other bolts than the specified bolt.
Always use the specified bolt that is surface treated.
• When loosening the specified bolt that is tightened, the treated surface may peel. Never reuse the specified
bolt that is tightened once.
TIGHTENING TORQUE CONTROL
Material made of aluminum die-casting parts is soft in term of hardness. Tightening torque must be controlled
exactly as specified. Always use a torque wrench to install any part to the specified tightening torque.
WARNING:
Never use a power tool to remove or tighten bolts for aluminum die-casting part to prevent damage to
aluminum die-casting parts.
EXHAUST SYSTEM
EX-3
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EX
N
P
O
REMOVAL AND INSTALLATION
EXHAUST SYSTEM
Exploded View
INFOID:0000000009161457
1.
Mounting bracket (No. 4)
2.
Main muffler assembly
3.
Bracket
4.
Mounting bracket (No. 3) (RH)
5.
Bracket
6.
Mounting bracket (No. 2)
7.
Gasket
8.
Sub muffler
9.
Gasket
10. Front cross bar assembly
11. Mounting bracket (No. 3) (LH)
Refer to
for symbols in the figure.
NNBIA0004GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст